Kubota V3300-E2B Скачать руководство пользователя страница 99

Страница: 99 / 140

S-36

V3300-E2B, V3300-T-E2B, WSM

DIESEL ENGINE

Injection Pump Unit (Continued)

(Reassembling the fuel injection pump unit)
1. Place the piston of the 4th cylinder at the top dead center in the

compression stroke. Fix the flywheel with the flywheel stopper.

2. Place the injection pump gear (1) back into the gear case

position. Make sure of aligning the align marks of the injection
pump gear (1) and the idle gear 2 (3).

3. Install the injection pump unit to the injection pump gear (1).

NOTE

■

• When installing the injection pump unit to the injection

pump gear, make sure that the key is fit in the keyway of
injection pump gear.

4. Temporarily tighten the injection pump gear mounting nut by

hand.

5. Fix the injection pump unit and tighten the injection pump gear

mounting nut to the specified torque.

6. Take off the fuel cam shaft lock screws (4) and tighten the plugs

(5) for plugging.

7. Loose the injection pump unit mounting nuts (7) for aligning the

injection timing.

8. Moving the injection pump unit clockwise (viewed from gear case

side), align the injection timing marks (6) on the injection pump
unit and on the gear case.

9. Tighten the injection pump unit mounting nut (7) to the specified

torque.

10.Reconnect the lubricating oil pipe (8) and place the injection

pump unit support and the gear cover of the injection pump unit.

11.Remove the flywheel stopper.
12.Check the injection timing. (See the “Injection Timing”.)
13.If the injection timing is not within the specification, repeat (7) to

(12) again.

W1176586

Tightening torque

Injection pump gear
mounting nut

73.6 to 83.4 N·m
7.5 to 8.5 kgf·m
54.2 to 61.5 ft-lbs

Injection pump unit
mounting nut

17.7 to 20.6 N·m
1.8 to 2.1 kgf·m
13.0 to 15.2 ft-lbs

(1) Injection Pump Gear
(2) Align mark of the Injection Gear
(3) Idle Gear 2
(4) Fuel Cam Shaft Lock Screw

(Socket Set Screw Dog Point Type)

(5) Plug
(6) Align Mark
(7) Injection Pump Unit Mounting Nut
(8) Lubricating Oil Pipe

KiSC issued 06, 2006 A

Содержание V3300-E2B













































































































































Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды

Kubota V3300-E2B, Руководство по ремонту

Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды