Kubota V3300-E2B Скачать руководство пользователя страница 111

Страница: 111 / 140

S-48

V3300-E2B, V3300-T-E2B, WSM

DIESEL ENGINE

Plate (Gear Case)

1. Remove the three plate mounting screws (1). Detach the plate

(2).

(When reassembling)

• Apply Three Bond 1217D adhesive or equivalent over the

shaded zones on both sides of the gasket that will be sandwiched
between the crankcase and plate.

• Be sure to fix the O-rings (3).

W1057656

(9) Piston and Connecting Rod

Oil Pan and Oil Strainer

1. Unscrew the oil pan mounting screws and remove the oil pan (1).
2. Unscrew the oil strainer mounting screw, and remove the oil

strainer (2).

(When reassembling)

• Install the oil strainer, using care not to damage the O-ring.
• Apply liquid gasket (Three Bond 1217D) to the oil pan as shown

in the figure.

• Confirm that the liquid gasket coating surface is free of water,

dust and oil in order to maintain sealing effect.

• Carefully apply the adhesive evenly.

NOTE

■

• When mounting the adhesive-applied parts, take care to fit

them to the mating parts.

• Assemble the adhesive-applied parts within ten minutes.
• To avoid uneven tightening, tighten mounting screws in

diagonal order from the center.

• After cleaning the oil strainer, install it.
• Attach the oil pan with its central drain plug facing toward

the air suction side.

W1057949

Tightening torque

Plate mounting screw

23.5 to 27.5 N·m
2.4 to 2.8 kgf·m
17.4 to 20.3 ft-lbs

(1) Plate Mounting Screw
(2) Plate
(3) O-ring

(4) Gasket
(5) Liquid Gasket

(1) Oil Pan
(2) Oil Strainer

(3) Liquid Gasket

KiSC issued 06, 2006 A

Содержание V3300-E2B













































































































































Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды

Kubota V3300-E2B, Руководство по ремонту

Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды