Kubota V3300-E2B Скачать руководство пользователя страница 62

Страница: 62 / 140

M-11

V3300-E2B, V3300-T-E2B, WSM

DIESEL ENGINE

6. TURBOCHARGER SYSTEM

[1] BOOST COMPENSATOR

The boost compensator is controlled by the boost

pressure of the control mechanism which controls
transient smoke caused by oversupply of fuel when the
engine starts and accelerates.

When the boost pressure is lower than working

pressure of the boost actuator (1), it prevents oversupply
of fuel to reduce transient smoke.

When the boost pressure is higher than working

pressure of the boost actuator (1), it controls the supply
of fuel to the equivalent of maximum power / rated speed
output.

The boost compensator adjusting screws (2) are set

and tamper-proof capped in factory, so never take off the
tamper-proof cap and readjust the screws.

W1014569

(1) Boost Actuator

(2) Boost Compensator Adjusting

Screw

KiSC issued 06, 2006 A

Содержание V3300-E2B













































































































































Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды

Kubota V3300-E2B, Руководство по ремонту

Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды