Kubota V3300-E2B Скачать руководство пользователя страница 137

Страница: 137 / 140

S-74

V3300-E2B, V3300-T-E2B, WSM

DIESEL ENGINE

Commutator and Mica

1. Check the contact face of the commutator for wear, and grind the

commutator with emery paper if it is slightly worn.

2. Measure the commutator O.D. with an outside micrometer at

several points.

3. If the minimum O.D. is less than the allowable limit, replace the

armature.

4. If the difference of the O.D.’s exceeds the allowable limit, correct

the commutator on a lathe to the factory specification.

5. Measure the mica undercut.
6. If the undercut is less than the allowable limit, correct if with a saw

blade and chamfer the segment edges.

W1075277

Brush Wear

1. If the contact face of the brush is dirty or dusty, clean it with emery

paper.

2. Measure the brush length (A) with vernier calipers.
3. If the length is less than the allowable limit, replace the yoke

assembly and brush holder.

W1075476

Brush Holder

1. Check the continuity across the brush holder and the holder

support with an ohmmeter.

2. If it conducts, replace the brush holder.

W1076066

Commutator O.D.

Factory spec.

32 mm
1.2598 in.

Allowable limit

31.4 mm
1.2362 in.

Mica under cut

Factory spec.

0.5 mm
0.0197 in.

Allowable limit

0.20 mm
0.0079 in.

(1) Segment
(2) Depth of Mica
(3) Mica

(a) Good
(b) Bad

Brush length (A)

Factory spec.

18.0 mm
0.7086 in.

Allowable limit

11.0 mm
0.4331 in.

(A) Brush Length

Resistance

Brush holder –
Holder support

Infinity

KiSC issued 06, 2006 A

Содержание V3300-E2B













































































































































Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды

Kubota V3300-E2B, Руководство по ремонту

Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды