Kubota V3300-E2B Скачать руководство пользователя страница 80

Страница: 80 / 140

S-17

V3300-E2B, V3300-T-E2B, WSM

DIESEL ENGINE

(2) Lubricating System

Engine Oil Pressure

1. Remove the oil switch and set a pressure tester (Code No.

07916-32032).

2. Start the engine. After warming up, measure the oil pressure of

both idling and rated speeds.

3. If the oil pressure is less than the allowable limit, check the

following.

• Engine oil insufficient
• Oil pump defective
• Oil strainer clogged
• Oil filter cartridge clogged
• Oil gallery clogged
• Excessive oil clearance
• Foreign matter in the relief valve

(When reassembling)

• After checking the engine oil pressure, tighten the engine oil

pressure switch to the specified torque.

W10349520

(3) Cooling System

Fan Belt Tension

1. Measure the deflection (A), depressing the belt halfway between

the fan drive pulley and alternator pulley at specified force 98 N
(10 kgf, 22 lbs).

2. If the measurement is not within the factory specifications, loosen

the alternator mounting screws and relocate the alternator to
adjust.

W1021011

Engine oil pressure

At idle
speed

Allowable
limit

49 kPa
0.5 kgf/cm

7 psi

At rated
speed

Factory
spec.

196 to 392 kPa
2.0 to 4.0 kgf/cm

28 to 57 psi

Allowable
limit

147.1 kPa
1.5 kgf/cm

21.3 psi

Tightening torque

Oil switch taper screw

14.7 to 19.6 N·m
1.5 to 2.0 kgf·m
10.8 to 14.5 ft-lbs

Deflection (A)

Factory spec.

10 to 12 mm
0.394 to 0.472 in.

(A) Deflection

KiSC issued 06, 2006 A

Содержание V3300-E2B













































































































































Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды

Kubota V3300-E2B, Руководство по ремонту

Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды