Kubota V3300-E2B Скачать руководство пользователя страница 101

Страница: 101 / 140

S-38

V3300-E2B, V3300-T-E2B, WSM

DIESEL ENGINE

Governor Fork Lever Assembly

1. Pull off the governor fork lever shaft (1) with the extra bolt (Dia :

4 mm, Pitch : 0.7 mm, Length : more than 25 mm) (2).

2. Unhook the governor spring (3) at the governor fork lever (4)

side.

3. Remove the governor fork lever assembly from the governor

housing (5).

(When reassembling)

• After reassembling the governor housing assembly, check the

movement of the governor fork lever assembly, the speed control
lever and the stop lever.

NOTE

■

• When assembling the inside parts, put the oil on each inside

part slightly.

• Be careful not to deform the start spring.

W1139749

Boost Arms (If equipped Boost Compensator)

1. Remove the boost actuator (1).
2. Remove the cir-clip (2).
3. Remove the boost arms (3) and the boost spring (4) from the pin

(5).

W1141511

(1) Governor Fork Lever Shaft
(2) Extra Bolt

(Dia : 4 mm, Pitch : 0.7 mm,
Length : more than 25 mm)

(3) Governor Spring
(4) Governor Fork Lever
(5) Governor Housing

Tightening torque

Boost actuator

39.2 to 45.1 N·m
4.0 to 4.6 kgf·m
28.9 to 33.3 ft-lbs

(1) Boost Actuator
(2) Cir-clip
(3) Boost Arm

(4) Boost Spring
(5) Pin

KiSC issued 06, 2006 A

Содержание V3300-E2B













































































































































Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды

Kubota V3300-E2B, Руководство по ремонту

Результаты поиска

Содержание V3300-E2B

Отзывы:

Похожие инструкции для V3300-E2B

Бренды по названию

Популярные бренды