Kubota LA535 Скачать руководство пользователя страница 45

Страница: 45 / 51

ASSEMBLY INSTRUCTIONS

17.Using the stand lever, lock the stands in the stowed

position. If impossible to slide the stand lever in the
upward completely, adjust the thread length of
connecting rod longer. If stand pin keeps on open
area, adjust the connecting rod shorter.

18. Set the stand lever in the unlocked position.

19. Fasten the seat belt and start the engine.
20. Raise the boom until the same height as step 1. Then

roll back the bucket to maximum.

21. With engine at idle, slowly dump the bucket until the

stand are in the stowed position. Check that the stands
are working correctly.

22. Raise the engine speed up to maximum. Then check

the procedures same as step 20 to 21.

23. Using the stand lever, lock the stands in the stowed

position.

(1) Stand lever
(2) Connecting pin
(3) Stand pin

(A) Correct storage position

(1) Stand lever

Содержание LA535




















































Результаты поиска

Содержание LA535

Отзывы:

Похожие инструкции для LA535

Бренды по названию

Популярные бренды

Kubota LA535, Руководство по сборке

Результаты поиска

Содержание LA535

Отзывы:

Похожие инструкции для LA535

Бренды по названию

Популярные бренды