KTM F8103S4 Скачать руководство пользователя

Страница: 29 / 36

SERVICE WORK ON THE CHASSIS 3

Info

The seconds can only be set to zero.
If no button is pressed for 15

–

20 seconds, or if an

impulse comes from the wheel speed sensor, the
settings are automatically saved and the setup menu is
closed.

3.36

Refueling

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

Note

Material damage

Inadequate fuel quality causes the fuel filter to quickly become clogged.

In some countries and regions, the available fuel quality and cleanliness may not be sufficient. This will result in
problems with the fuel system.

–

Refuel only with clean fuel that meets the specified standards.

Note

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to enter the groundwater, the soil, or the sewage system.

Preparatory work

–

Switch off the engine.

–

Fold the seat up. (

p. 18)

–

Open fuel tank filler cap. (

p. 28)

Содержание F8103S4





































Результаты поиска

Содержание F8103S4

Отзывы:

Похожие инструкции для F8103S4

Бренды по названию

Популярные бренды

KTM F8103S4, Инструкции по установке

Результаты поиска

Содержание F8103S4

Отзывы:

Похожие инструкции для F8103S4

Бренды по названию

Популярные бренды