KTM F8103S4 Скачать руководство пользователя страница 30

Страница: 30 / 36

3 SERVICE WORK ON THE CHASSIS

F01694-10

Main work

–

Fill the fuel tank with fuel up to level

Guideline

Dimension

30 mm (1.18 in)

Total fuel tank
capacity, approx.

5 l
(1.3 US gal)

Super unleaded
(ROZ 95/RON
95/PON 91)
(

p. 32)

Info

Observe the labels on the fuel pump.

Finishing work

–

Close the fuel tank filler cap. (

p. 29)

–

Lock the seat. (

p. 19)

3.37

Opening fuel tank filler cap

Danger

Fire hazard

Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–

Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

–

Switch off the engine for refueling.

–

Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–

If any fuel is spilled, wipe it off immediately.

–

Observe the specifications for refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

–

Avoid skin, eye and clothing contact with fuel.

–

Immediately consult a doctor if you swallow fuel.

–

Do not inhale fuel vapors.

–

In case of skin contact, rinse the affected area with plenty of water.

–

Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–

Change your clothing in case of fuel spills on them.

–

Keep fuels correctly in a suitable canister, and out of the reach of children.

Note

Environmental hazard

Improper handling of fuel is a danger to the environment.

–

Do not allow fuel to enter the groundwater, the soil, or the sewage system.

Содержание F8103S4





































Результаты поиска

Содержание F8103S4

Отзывы:

Бренды по названию

Популярные бренды

KTM F8103S4, Инструкции по установке

Результаты поиска

Содержание F8103S4

Отзывы:

Бренды по названию

Популярные бренды