KTM 450 SMR 2021 Скачать руководство пользователя | Manualshive

Страница: 75 / 139

background image

BRAKE SYSTEM 12

73

12.1

Adjusting the basic position of the hand brake lever

H01726-11

–

Adjust the basic position of the hand brake lever to your hand
size by turning adjusting wheel

1

.

Info

Push the hand brake lever forward and turn the adjust-
ing wheel.
Turn the adjusting wheel clockwise to increase the
distance between the hand brake lever and the han-
dlebar.
Turn the adjusting wheel counterclockwise to decrease
the distance between the hand brake lever and the han-
dlebar.
The range of adjustment is limited.
Only turn the adjusting wheel by hand; do not use
force.
Do not make any adjustments while riding.

12.2

Checking the brake discs

Warning

Danger of accidents

Worn-out brake discs reduce the braking effect.

–

Make sure that worn-out brake discs are replaced immediately. (Your authorized KTM workshop will
be glad to help.)

400257-10

–

Check the front and rear brake disc thickness at multiple
points for the dimension

A

.

Info

Wear reduces the thickness of the brake disc around
the contact surface of the brake linings.

Brake discs - wear limit

front

4.5 mm (0.177 in)

rear

3.5 mm (0.138 in)

» If the brake disc thickness is less than the specification:

–

Change the front brake disc.

–

Change the rear brake disc.

–

Check the front and rear brake discs for damage, cracking, and
deformation.
» If the brake disc exhibits damage, cracking, or deforma-

tion:

–

Change the front brake disc.

–

Change the rear brake disc.

«
...
73
74
75
76
77
...
»

Содержание 450 SMR 2021












































































































































Отзывы:

Нет отзывов

Похожие инструкции для 450 SMR 2021

Бренд: Honda Страницы: 118

Бренд: hepco & becker Страницы: 6

Бренд: KEEWAY Страницы: 164

Бренд: Dakota Digital Страницы: 6

COMFORT 10130810

Бренд: Contracor Страницы: 36

HIGHSIDER VICTORY

Бренд: Paaschburg & Wunderlich Страницы: 5

Бренд: DAELIM Страницы: 93

640 LC4 ENDURO 2006

Бренд: KTM Страницы: 60

2001 GSX1300RK1 HAYABUSA

Бренд: Suzuki Страницы: 31

Бренд: X-lite Страницы: 84

Бренд: MOTO GUZZI Страницы: 266

Бренд: MRA Страницы: 8

Бренд: Honda Страницы: 4

Бренд: Silvercrest Страницы: 42

Бренд: JIMS Страницы: 2

Бренд: AGUSTA Страницы: 427

Rumbler 500 2017

Бренд: Royal Enfield Страницы: 160

Бренд: Wunderlich Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды