KTM 450 SMR 2021 Скачать руководство пользователя страница 104

Страница: 104 / 139

16 TUNING THE ENGINE

102

16.4

Changing the mapping

Info

The desired engine characteristic can be activated via the

MAP

button on the combination switch.

The setting most recently selected is activated again when restarting.
The traction control can also be activated in each mapping using the

button.

The mapping can also be changed during the ride.

H02889-01

Activating STANDARD mapping:

–

Press button

MAP

until LED

lights up.

Guideline

Engine speed

< 4,000 rpm

STANDARD

–

balanced response

H02886-01

Activating ADVANCED mapping:

–

Press button

MAP

until LED

lights up.

Guideline

Engine speed

< 4,000 rpm

ADVANCED

–

direct response

16.5

Adjusting the idle speed

Warning

Danger of accidents

The engine may go out spontaneously if the idle speed is set too low.

–

Set the idle speed to the specified value. (Your authorized KTM workshop will be glad to help.)

Содержание 450 SMR 2021












































































































































Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Бренды по названию

Популярные бренды

KTM 450 SMR 2021, Руководство пользователя

Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Бренды по названию

Популярные бренды