KTM 450 SMR 2021 Скачать руководство пользователя

Страница: 70 / 139

11 SERVICE WORK ON THE CHASSIS

F00398-01

–

Check that the chain guide is firmly seated.
» If the chain guide is loose:

–

Tighten the screws on the chain guide.
Guideline

Remaining screws,
chassis

10 Nm
(7.4 lbf ft)

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 42)

11.37

Checking the frame

K01114-01

–

Check the frame for damage, cracking, and deformation.
» If the frame shows signs of damage, cracking, or deforma-

tion:

–

Change the frame.
Guideline

Repairs on the frame are not permitted.

11.38

Checking the link fork

401520-01

–

Check the link fork for damage, cracking, and deformation.
» If the link fork shows signs of damage, cracking, or defor-

mation:

–

Change the link fork.

Info

Always replace a damaged link fork. Repairing
the link fork is not authorized by KTM.

11.39

Checking the throttle cable routing

Preparatory work

–

Remove the fuel tank.

(

p. 60)

Содержание 450 SMR 2021












































































































































Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды

KTM 450 SMR 2021, Руководство пользователя

Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды