KTM 450 SMR 2021 Скачать руководство пользователя

Страница: 89 / 139

WHEELS, TIRES 13

H03002-10

–

Remove spacers

13.4

Installing the rear wheel

Warning

Danger of accidents

Oil or grease on the brake discs reduces the braking effect.

–

Always keep the brake discs free of oil and grease.

–

Clean the brake discs with brake cleaner when necessary.

H03001-10

Main work

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change the rear wheel bearing.

–

Clean and grease shaft seal rings

and contact surfaces

of the spacers.

Long-life grease (

p. 128)

–

Insert the spacers.

F00412-10

–

Clean and grease the wheel spindle.

Long-life grease (

p. 128)

–

Position rear wheel and insert wheel spindle

The brake linings are correctly positioned.

–

Mount the chain.

Содержание 450 SMR 2021












































































































































Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды

KTM 450 SMR 2021, Руководство пользователя

Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды