KTM 450 SMR 2021 страница 59 Скачать руководство пользователя

Страница: 59 / 139

SERVICE WORK ON THE CHASSIS 11

E01964-10

Main work

–

Detach retaining tab

–

Remove air filter with air filter support.

–

Remove air filter from air filter support.

11.25

Installing the air filter

H02459-01

Main work

–

Mount the clean air filter on the air filter support.

–

Grease the air filter in area

Long-life grease (

p. 128)

E01965-10

–

Insert air filter and position retaining pin

in bushing

The air filter is correctly positioned.

–

Insert retaining tab

Retaining pin

is secured by retaining tab

Info

If the air filter is not mounted correctly, dust and dirt
may enter the engine and result in damage.

Finishing work

–

Install the air filter box cover. (

p. 56)

11.26

Cleaning the air filter and air filter box

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with
the applicable regulations.

Info

Do not clean the air filter with fuel or petroleum since these substances attack the foam.

Preparatory work

–

Remove the air filter box cover. (

p. 56)

–

Remove the air filter.

(

p. 56)

Содержание 450 SMR 2021












































































































































Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды

KTM 450 SMR 2021, Руководство пользователя

Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды