KTM 450 SMR 2021 страница 16 Скачать руководство пользователя

Страница: 16 / 139

6 CONTROLS

6.1

Clutch lever

E01951-10

The clutch lever

is fitted on the left side of the handlebar.

The clutch is hydraulically operated and self-adjusting.

6.2

Hand brake lever

H01726-10

Hand brake lever

is fitted on the right side of the handlebar.

The front brake is engaged using the hand brake lever.

6.3

Throttle grip

H01728-10

The throttle grip

is fitted on the right side of the handlebar.

6.4

Stop button

E01952-10

The stop button

is fitted on the left side of the handlebar.

Possible states

• The stop button

is in the basic position

–

In this position,

the ignition circuit is closed and the engine can be started.

• Stop button

pressed

–

In this position, the ignition circuit

is interrupted, a running engine stops, and a non-running
engine will not start.

Содержание 450 SMR 2021












































































































































Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды

KTM 450 SMR 2021, Руководство пользователя

Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды