manualshive.com logo in svg

KSM-Stoker KSM-Multistoker 775-75 PCT 400, Инструкция по эксплуатации, Страница: 9 / 50

Поделиться
Скачать
KSM-Stoker KSM-Multistoker 775-75 PCT 400 Скачать руководство пользователя страница 9

 

- 8 - 

 

 

 

3.1 Pushbuttons. 

 
The panel is equipped with three pushbuttons which changes indications depending on where you are in 
the program. 
When the boiler is in the normal run screen the designations are as follows: 
 

“

↑

” “

↓

” “MENU” 

 
“

↑

”:  

Activates the stoker screw as long as the button is pushed. 

 
“

↓

”:  

A short push and the stoker screw will stop (the LED turn red). If you push a little longer 
the whole system will shut down. (Please notice chapter 7 concerned shutting down the 
system).  

 
“MENU” 

With this button the menu is activated and here it is possible for you to make your desired 

adjustments. If you have had an alarm it will write “BACK” above the menu button. Please press this 
button to leave the alarm. 
 
With the “

↑

” and “

↓

” you can scroll to your desired adjustment. To make the adjustment please push the 

“MENU” button. 
 
 
   
 

 

Содержание KSM-Multistoker 775-75 PCT 400



















































Отзывы:

Нет отзывов