background image

instructions regarding safety and operating proce-

dures.

5.1.3 

BATTERY INSTALLATION

To insert batteries in the battery compartment 

(Photo I - 2) it is necessary to lower the brush 

plate to the floor.

To access to the battery compartment, pull the 

opening lever (Photo H - 1) and lift the recovery 

tank (Photo N - 3).

Detach the spring clip (Photo I - 1) placed on the 

lifting cable of the brush plate.

Place the batteries in the battery compartment 

(Photo I - 2) checking that they are in perfect con-

ditions.

5.1.4 

BATTERY CONNECTION

These operations must be carried out by specia-

lized personnel.

Install and charge the batteries in a dry ventila-

ted place, far from sources of heat and corrosive

substances. Make sure that the voltage between

the batteries and the battery charger corresponds.

Protect the circuit with a delay switch or a fuse with

a higher charge than the maximum absorption of

the battery charger. Comply with the polarity of the

battery plug.

Disconnect the Anderson connector of the battery

wiring from the Anderson connector of the machine

wiring (Photo D - 7) (Photo F - 8) . Always hold

the connectors with the hands and never pull on

the cables.

Photo H  show connection diagram of the batteries

for B - BT machines.

Attach the battery wiring to the battery,

connecting the terminals only on the poles

marked with the same symbol (red wiring

“+”, black wiring “-“)!

A battery short-circuit may cause an explo-

sion!

After checking that all the controls on the panel

are in position “0” or at rest, connect the battery

connector to the machine connector.

( ! ) Close the battery compartment making sure

not to crush any wires.

Photo I - 3 show the correct connection of the bat-

teries for B - BT machines.

5.1.5 

CIRCUIT BOARD SETTINGS CONFI-

GURATION

The machine is equipped to GEL battery circuit 

board configured. If the operator whish to use e 

Pb-Acid battery, it is necessary to set the electronic 

circuit board as follows:

Model “B” (DC 24V)

TO ENTER THE BATTERY THRESHOLD CONFI-

GURATION MODE:

1) Press simultaneously the push buttons “BRUSH

MOTOR SWITCH” (Photo C - 1) and “SUCTION 

MOTOR SWITCH” (Photo C - 2) within 2 seconds 

after switching on the machine with the key switch 

(Photo D - 1). The three LED of the battery power 

test (Photo C - 3A, 3B, 3C ) will be ON.

2) Press “SUCTION MOTOR SWITCH” key within 5

seconds from the previous action; you have now

entered in the configuration mode: the green and

yellow LED of the battery power test (Photo C - 3A,

3B ) will be ON.

THE CONFIGURATION SETTINGS ARE VISIBLE

ON THE BRUSH MOTOR SWITCH SIGNAL LED

(Photo C - 2A ):

1) OFF: Pb-Acid.

2) ON: Gel.

TO MODIFY CONFIGURATION SETTINGS:

Press the  “BRUSH MOTOR SWITCH” (Photo C - 1)

TO SAVE THE SETTINGS AND EXIT THE MODE:

Press  the “SUCTION MOTOR SWITCH” (Photo C

- 2)

Once the settings have been set, we have different 

battery discharge levels with differentiated inter-

vention on the machine functions as specified in 

the following table:

Battery discharge indicator and functions - Model “B” 

(DC 24V)

Volts

Battery Type

Battery power 
test indicator 
LED

Brush opera-
tion indicator 
LED

Pb-Acid

GEL

Signaling

Signaling

Action

24,0

24,0

Green

LED ON

LED ON

All working

21,5

22,5

Yellow

LED ON

LED ON

All working

20,5

21,5

Red LED ON

LED 

FLASHING

Brush 

motor is 

not wor-

king

20,0

21,0

Red LED 

FLASHING

LED 

FLASHING

Brush and 

suction mo-
tors are not 

working

Model “BT” (DC 24V with traction)

TO ENTER THE BATTERY THRESHOLD CONFI-

GURATION MODE:

1) Press simultaneously the push buttons “RE-

DUCE SPEED” (Photo E - 3) and “SUCTION MOTOR

www.kruger.es

Página 30 de 42

Manual KFL50E-KFL50BBC-KFL50BBCTR

Содержание KFL50BBC

















































Отзывы: