Kruger KFL50BBC, Руководство пользователя

Страница: 32 / 48

SWITCH” (Photo E - 6) within 2 seconds after
switching on the machine with the key switch
(Photo F - 1). The second LED of the speed indica-
tor (Photo E - 3B ) will be ON.
2) Press “INCREASE SPEED” (Photo E - 4)” key
within 5 seconds from the previous action; you
have now entered in the configuration mode.
•
THE CONFIGURATION SETTINGS ARE VISIBLE
ON THE SPEED INDICATOR LED:
1) The first two LEDs (Photo E - 3A, 3B) indicate
the type of setting of the indicator intervention th-
reshold an both must be ON;
2) The third and fourth LEDs (Photo E - 3C, 3D)
indicate the battery type: for the PB-Acid battery
only the third LED (Photo E - 3C ) should be ON,
while for the GEL battery both should be ON (Photo
E - 3C, 3D)
•
TO MODIFY CONFIGURATION SETTINGS:
1) The “INCREASE SPEED” (Photo E - 4)” and “RE-
DUCE SPEED” (Photo E - 3) keys are used to set
the indicator’s intervention threshold in such a way
that the first two speed indicators LEDs (Photo E -
3A, 3B) turn ON;
2) The “BRUSH MOTOR SWITCH” (Photo E - 5)
is used to set the PB-Acid battery type while the
“SUCTION MOTOR SWITCH” (Photo E - 6) is used
to set the GEL battery type
•
TO SAVE THE SETTINGS AND EXIT THE MODE:
Press the “REDUCE SPEED” (Photo E - 3) switch
and the “SUCTION MOTOR SWITCH” (Photo E - 6)
simultaneously.
Once the settings have been set, we have different
battery discharge levels with differentiated inter-
vention on the machine functions as specified in
the following table:
Battery discharge indicator and functions - MODEL “BT”
(DC 24V with traction)
Volts
Battery Type
B a t t e r y
power test
i n d i c a t o r
LED Brush ope-
ration indi-
cator LED
Pb-Acid GEL Signaling Signaling Action
24,0 24,0 Green
LED ON
LED ON All working
21,5 22,5 Yellow
LED ON
LED ON All working
20,5 21,5 Red LED ON LED
FLASHING
Brush motor
is not wor-
king
Battery discharge indicator and functions - MODEL “BT”
(DC 24V with traction)
Volts
Battery Type
B a t t e r y
power test
i n d i c a t o r
LED Brush ope-
ration indi-
cator LED
20,0 21,0 Red LED
FLASHING
LED
FLASHING
Brush and
suction mo-
tors are not
working
If you do not complete the configuration proce-
dure, the settings remain as they were originally.
( ! ) We recommend to call the assistance centre
or a technician if you have problems with the set-
tings given.
Do not open or tamper the electronic board.
5.2 BATTERY CHARGER CONFIGURA-
TION
The machine is equipped with a battery charger
configurated for GEL batteries
To change the battery charger settings read the
manual provided by the battery charger manufac-
turer.
6. OPERATING INFORMATION
6.1 MACHINE PREPARATION
•
Before starting to work, wear non-slip shoes,
gloves and any other personal protection device
indicated by the supplier of the detergent used or
considered necessary based on the operating en-
vironment.
☞
Do the following before starting to work. Refer
to the relative sections for a detailed description of
these steps:
Heck the battery charge level and charge, if ne-
cessary.
Mount the brushes or scraper disks (with the abra-
sive disks) that are suitable for the surface and
work involved.
Mount the squeegee, check that it is solidly atta-
ched and connected to the suction hose and that
the drying blades are not too worn.
Make sure that the recovery tank is empty. If not,
empty it completely.
Check and completely close the detergent solution
release control.
Fill the detergent solution tank with a mix of clean
water and non-foaming detergent in an adequate
concentration through the anterior hole. Leave 2
cm between the mouth of the plug and the level
of the liquid.
☞
To avoid risks, become familiar with the machine
movements, carrying out test runs on a large sur-
face without obstacles.
To obtain the best results in terms of cleaning and
equipment service life, you should do the following
www.kruger.es Página 31 de 42
Manual KFL50E-KFL50BBC-KFL50BBCTR