manualshive.com logo in svg

kozy heat CALLAWAY ST, Инструкция по установке и эксплуатации

Поделиться
Скачать
kozy heat CALLAWAY ST Скачать руководство пользователя страница 40

40

  FACING AND FINISHING

Hussong Mfg. Co., Inc. • Kozy Heat Fireplaces

#CLW-ST R.1 February 2021

4.2  Optional Finishing Trim 

Kit (FTK): CWST-FTK

IMPORTANT: Finishing trim kit assembly must be attached before 

fireplace installation.

This finishing trim kit (included with the fireplace) provides a deeper 

finishing edge for finishing materials such as stone.
You may need to mark and pre-drill holes before fastening trim 

panels to fireplace.

Kit includes:

 (8) trim panel pieces; (36) screws 

1.  Install top trim panel. Fasten to fireplace with screws through the 

holes in the trim panel. 

2.  Install side trim panels. Fasten to fireplace with screws through 

the holes in the trim panels.

3.  Install bottom trim panel. Fasten to fireplace with screws through 

the holes in the trim panel.

4.  Repeat for the other side of the fireplace.  

Figure 4.7, Optional Finishing Trim Kit #CWST-FTK

Содержание CALLAWAY ST
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды