kozy heat 961 DV Скачать руководство пользователя страница 1

This appliance may be installed in an aftermarket permanently located, manufactured home (USA

only) or mobile home, where not prohibited by local codes.  This appliance is only for use with the

type(s) of gas indicated on the rating plate.  This appliance is convertible for use with other gases. 

An LP Gas conversion kit is included.

WARNING: If the information in these
instructions are not followed exactly, a fire
or explosion may result causing property
damage, personal injury or loss of life.

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch electrical switches; do not use

the phone in your building.

Immediately call your gas supplier from a

neighbor’s phone.  Follow the gas suppliers

instructions.

If you cannot reach your gas supplier, call the

fire department.

Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

Model #961 DV

Installation & Operating

Instructions

WARNING:

Improper installation, adjustment, alteration, service or maintenance can cause injury, property damage, or
loss of life.  Refer to this manual for assistance.  For additional information, consult a qualified installer, service
agency or the gas supplier.

IMPORTANT:

READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLATION.   FAILURE TO

INSTALL THIS FIREPLACE CORRECTLY CAN CAUSE SERIOUS STRUCTURAL AND FIRE

HAZARDS AND MAY VOID YOUR WARRANTY.

 

 

 

 

 

 

 

 

 

 

 

 

                                                                                                                                                                                                 February 2008

Содержание 961 DV



































Отзывы: