Korg PA1X, Руководство пользователя

Страница: 16 / 424

12
Front panel
FULL (both LEDs On)
Chords are detected on the full keyboard range.
You must always play three or more notes to let
the arranger recognize a chord. (You can use this
mode even when the Split Keyboard Mode is
selected).
OFF No chords detected. After pressing START/STOP,
only the Drum and Percussion accompaniment
tracks can play.
`
KEYBOARD MODE section
These buttons define how the four Keyboard tracks are posi-
tioned on the keyboard.
SPLIT The Lower track plays below the split point, while
the Upper 1, Upper 2 and Upper 3 tracks play
above it. By default, selecting this keyboard mode
automatically selects the Lower chord scanning
mode (see “Chord Recognition Mode” on
page 95).
FULL UPPER
The Upper 1, Upper 2 and/or Upper 3 tracks play
on the whole keyboard range. The Lower track
does not play. By default, selecting this keyboard
mode automatically selects the Full chord scan-
ning mode (see “Chord Recognition Mode” on
page 95).
a
STYLE CHANGE
This button turns the Style Change function on or off.
On When you select a Performance, the Style could
change, according to which Style number is
memorized onto the Performance.
Off When you select a Performance, the Style and
Style track settings remain unchanged. Only Key-
board track settings are changed.
b
PERFORMANCE SELECT
Press this button to use the SOUND/PERFORMANCE SELECT
section to select a Performance.
c
SOUND SELECT
Press this button to use the SOUND/PERFORMANCE SELECT
section to select a Sound, and assign it to the selected track.
d
SOUND/PERFORMANCE SELECT section
Use these buttons to open the Sound Select or Performance
Select window, and select a Sound or a Performance. See “Sound
Select window” on page 74, or “Performance Select window” on
page 74. For a list of available Sounds, see “Sounds” on page 291.
The leftmost button selects the upper or lower row of Sound or
Performance banks. Press it repeatedly to select one of the rows.
Upper LED On Upper row of Sounds or Performances selected.
Lower LED On Lower row of Sounds or Performances selected.
Both LEDs On Additional EXB card’s Sounds or Performances
selected.
On the front panel, Sound banks are identified by the instru-
ment names, while Performance banks are identified by num-
bers (1-10; 0=bank 10).
A note about Sound banks and names. Sounds from “PIANO”
to “SFX” are standard Sounds, the user can’t directly modify.
Sounds “USER1” and “USER2” are locations where you can load
new Sounds from disk.
“USER DK” is where you can load new Drum Kits.
Each Sound bank contains various pages, each with up to eight
Sounds. Repeatedly press a bank button to cycle between the
available pages.
e
ASSIGNABLE SWITCH (1-4)
You can assign any function to these switches. See “Pad/Switch:
Assignable Switch” on page 94 for more information.
f
PAD (1-4, STOP)
Each Pad corresponds to a dedicated Pad track. Use these but-
tons to trigger up to four sounds or sequences at the same time.
• Press a single PAD button to trigger a single sound or
sequence.
• Press more PAD buttons to trigger several sounds or
sequences.
The sequences will play up to the end. Then, they will stop or
continue repeating, depending on their “One Shot/Loop” status
(see “Pad Type” on page 133).
You can stop all sequences, or just some of them, by pressing the
STOP button of the PAD section:
• Press STOP to stop all sequences at once.
• Keep STOP pressed and press one (or more) of the PAD
buttons to stop the corresponding sequence(s).
Note: Pads share polyphony voices with the other tracks, so avoid
using too many of them together with a dense Style or Song
arrangement.
About Pad synchronization. In Style Play mode, Pads are sync’d
to the Style’s tempo. In Song Play mode, they are sync’d to the
last Sequencer you set to play. For example, assume you pressed
SEQ2-PLAY; when pressing one of the PAD buttons, it will play
in sync with Sequencer 2.
Note: There is no synchronization with MP3 files and Audio CD
Tracks. Pads can only be synchronized to Standard MIDI Files.
Therefore, when an MP3 file or Audio CD Track is assigned to the
last select Sequencer, Pads will synchronize to the last Standard
MIDI File that has been played back.
About Pads’ and the Sequencers’ Play command. When you
press one of the PLAY buttons to start the corresponding
Sequencer, all Pads will stop playing.
g
TRANSPOSE
These buttons transpose the whole instrument in semitone steps
(Master Transpose). The transposition value is usually shown on
the page header in the display.
Press both buttons together, to reset the Master Transpose to
zero.
SB
Sty SB
SB
SB
SB
Sty
SB