- 56 -
Mounting the wall brackets
Remove the plate and fixing screw from each wall bracket. Turn the adjustment screw counterc-
lockwise using a 6mm allen key. Measure the distance in figure 3. The distance must be greater
than 40 mm (if the distance is 45 mm, the awning's angle of inclination is 80°). The distance must
be the same for all wall brackets.
Mounting of wall brackets
②
Picture 2 is the installation distance from awning to wall or ceiling.
Remove the plate and the retaining screw of each wall
bracket. Turning adjusting screw with a hex key 6 mm in
otherwise clockwise. Measure the distance in Figure-3.
This distance must be greater than 40 mm, (when the
③
W
all
W
all
Ceiling
L
α°
In
st
al
la
tio
n
he
ig
ht : C
H
ei
gh
t o
f f
ro
nt
li
ne
:
H
α°
75°
80°
60°
65°
70°
C
H+650mm
H+450mm
H+850mm
H+1050mm
H+1250mm
Pls make sure the heigth before installation according to
the height of front bar (H) and
the angle of
sunshine(α°). After open the awning, the height must up
to human so it can protect your head from hitting the
awning.
Pls make sure the height and position before installation
WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered
operation.
Install the actuating member of a manual release at a height less than 1.8 m.
A horizontal distance of at least 0.4 m is to be maintained between the fully unrolled driven part and any permanent
object.
Prior to installation
●
Carefully unpack the awning and dispose of the packaging materials by environmentally-friendly means.
●
Beware of the sudden unfolding of any parts, especially the folding arms.
Installation procedure
Choosing the right location
Suitable wall types: reinforced concrete walls, brick walls. The chosen wall must be suitable
to hold and maintain the awning. We will not be responsible for any damage to persons, to
the property and to the awning due to weak support of installation wall.
6
L=2.5M
L=3M
H+780mm
H+520mm
H+1030mm
H+1270mm
H+1500mm
L=3.5M
H+900mm
H+600mm
H+1200mm
H+1480mm
H+1750mm
Installation
WARNING:
Important safety information. Follow all instructions, as incorrect installation can lead
to serious injuries. Before installing the drive, remove unnecessary cables and render any parts
not required for operation ineffective. Install the manual control's release at a height lower than
1.80m. A distance of at least 0.4 m must be maintained between the fully unrolled part and any
stationary object.
Prior to installation
● The awning must be unpacked carefully and the packaging material disposed of in an
environmentally friendly manner.
● Avoid the sudden unfolding of parts, especially the arms.
Selecting the right spot
Suitable wall types:
reinforced concrete walls, brick walls. The selected wall must be suitable for
holding the awning. We accept no liability for damage to the building and awning caused by the
wall's lack of load-bearing capacity.
Please check the height and position of the awning prior to installation.
Height of front line: H
Installation height: C
Figure 2 shows the installation distance between
the awning and the wall or ceiling.
Mounting of wall brackets
②
Picture 2 is the installation distance from awning to wall or ceiling.
Remove the plate and the retaining screw of each wall
bracket. Turning adjusting screw with a hex key 6 mm in
otherwise clockwise. Measure the distance in Figure-3.
This distance must be greater than 40 mm, (when the
distance equal to 45 mm, the angle of inclination of
awning is 80 °). Must be the same distance for all wall
brakcets.
Pressing block
Hex key
Adjusting bolt
③
W
all
W
all
Ceiling
L
α°
In
st
al
la
tio
n
he
ig
ht : C
H
ei
gh
to
ff
ro
nt
line
:H
α°
75°
80°
60°
65°
70°
C
H+650mm
H+450mm
H+850mm
H+1050mm
H+1250mm
Pls make sure the heigth before installation according to
the height of front bar (H) and
the angle of
sunshine(α°). After open the awning, the height must up
to human so it can protect your head from hitting the
awning.
Pls make sure the height and position before installation
WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered
operation.
Install the actuating member of a manual release at a height less than 1.8 m.
A horizontal distance of at least 0.4 m is to be maintained between the fully unrolled driven part and any permanent
object.
Prior to installation
●
Carefully unpack the awning and dispose of the packaging materials by environmentally-friendly means.
●
Beware of the sudden unfolding of any parts, especially the folding arms.
nstallation procedure
Choosing the right location
Suitable wall types: reinforced concrete walls, brick walls. The chosen wall must be suitable
to hold and maintain the awning. We will not be responsible for any damage to persons, to
the property and to the awning due to weak support of installation wall.
6
L=2.5M
L=3M
H+780mm
H+520mm
H+1030mm
H+1270mm
H+1500mm
L=3.5M
H+900mm
H+600mm
H+1200mm
H+1480mm
H+1750mm
nting of wall brackets
②
ure 2 is the installation distance from awning to wall or ceiling.
emove the plate and the retaining screw of each wall
cket. Turning adjusting screw with a hex key 6 mm in
otherwise clockwise. Measure the distance in Figure-3.
This distance must be greater than 40 mm, (when the
distance equal to 45 mm, the angle of inclination of
awning is 80 °). Must be the same distance for all wall
brakcets.
Pressing block
Hex key
Adjusting bolt
③
W
all
W
all
Ceiling
L
α°
In
st
al
la
tio
n
he
ig
ht : C
H
ei
gh
to
ff
ro
nt
line
:H
α°
75°
80°
60°
65°
70°
C
H+650mm
H+450mm
H+850mm
H+1050mm
H+1250mm
Pls make sure the heigth before installation according to
the height of front bar (H) and
the angle of
sunshine(α°). After open the awning, the height must up
to human so it can protect your head from hitting the
awning.
make sure the height and position before installation
WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
ore installing the drive, remove any unnecessary cords and disable any equipment not needed for powered
operation.
all the actuating member of a manual release at a height less than 1.8 m.
A horizontal distance of at least 0.4 m is to be maintained between the fully unrolled driven part and any permanent
ct.
to installation
Carefully unpack the awning and dispose of the packaging materials by environmentally-friendly means.
Beware of the sudden unfolding of any parts, especially the folding arms.
tallation procedure
Choosing the right location
Suitable wall types: reinforced concrete walls, brick walls. The chosen wall must be suitable
to hold and maintain the awning. We will not be responsible for any damage to persons, to
the property and to the awning due to weak support of installation wall.
6
L=2.5M
L=3M
H+780mm
H+520mm
H+1030mm
H+1270mm
H+1500mm
L=3.5M
H+900mm
H+600mm
H+1200mm
H+1480mm
H+1750mm
Ceiling
W
all
W
all
Mounting of wall brackets
②
Picture 2 is the installation distance from awning to wall or ceiling.
Remove the plate and the retaining screw of each wall
bracket. Turning adjusting screw with a hex key 6 mm in
otherwise clockwise. Measure the distance in Figure-3.
This distance must be greater than 40 mm, (when the
distance equal to 45 mm, the angle of inclination of
awning is 80 °). Must be the same distance for all wall
brakcets.
Pressing block
Hex key
Adjusting bolt
③
W
all
W
all
Ceiling
L
α°
In
st
al
la
tio
n
he
ig
ht : C
H
ei
gh
to
ff
ro
nt
line
:H
α°
75°
80°
60°
65°
70°
C
H+650mm
H+450mm
H+850mm
H+1050mm
H+1250mm
Pls make sure the heigth before installation according to
the height of front bar (H) and
the angle of
sunshine(α°). After open the awning, the height must up
to human so it can protect your head from hitting the
awning.
Pls make sure the height and position before installation
WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered
operation.
Install the actuating member of a manual release at a height less than 1.8 m.
A horizontal distance of at least 0.4 m is to be maintained between the fully unrolled driven part and any permanent
object.
Prior to installation
●
Carefully unpack the awning and dispose of the packaging materials by environmentally-friendly means.
●
Beware of the sudden unfolding of any parts, especially the folding arms.
Choosing the right location
Suitable wall types: reinforced concrete walls, brick walls. The chosen wall must be suitable
to hold and maintain the awning. We will not be responsible for any damage to persons, to
the property and to the awning due to weak support of installation wall.
L=2.5M
L=3M
H+780mm
H+520mm
H+1030mm
H+1270mm
H+1500mm
L=3.5M
H+900mm
H+600mm
H+1200mm
H+1480mm
H+1750mm
Allen key
Adjustment screw
Pressing block
Mounting of wall brackets
②
Picture 2 is the installation distance from awning to wall or ceiling.
Remove the plate and the retaining screw of each wall
bracket. Turning adjusting screw with a hex key 6 mm in
otherwise clockwise. Measure the distance in Figure-3.
This distance must be greater than 40 mm, (when the
distance equal to 45 mm, the angle of inclination of
awning is 80 °). Must be the same distance for all wall
brakcets.
Pressing block
Hex key
Adjusting bolt
③
W
all
W
all
Ceiling
L
α°
In
st
al
la
tio
n
he
ig
ht : C
H
ei
gh
to
ff
ro
nt
line
:H
α°
75°
80°
60°
65°
70°
C
H+650mm
H+450mm
H+850mm
H+1050mm
H+1250mm
Pls make sure the heigth before installation according to
the height of front bar (H) and
the angle of
sunshine(α°). After open the awning, the height must up
to human so it can protect your head from hitting the
awning.
Pls make sure the height and position before installation
WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered
operation.
Install the actuating member of a manual release at a height less than 1.8 m.
A horizontal distance of at least 0.4 m is to be maintained between the fully unrolled driven part and any permanent
object.
Prior to installation
● Carefully unpack the awning and dispose of the packaging materials by environmentally-friendly means.
● Beware of the sudden unfolding of any parts, especially the folding arms.
nstallation procedure
Choosing the right location
Suitable wall types: reinforced concrete walls, brick walls. The chosen wall must be suitable
to hold and maintain the awning. We will not be responsible for any damage to persons, to
the property and to the awning due to weak support of installation wall.
6
L=2.5M
L=3M
H+780mm
H+520mm
H+1030mm
H+1270mm
H+1500mm
L=3.5M
H+900mm
H+600mm
H+1200mm
H+1480mm
H+1750mm
GB
Содержание BW31000LED
