18-28
Effects
Mod./P.Shift
038: Pitch-
Shift
(Pitch Shifter)
This effect changes the pitch of the input signal. You can
select from three types: Fast (quick response), Medium, and
Slow (preserves tonal quality). You can also create an effect in
which the pitch is gradually raised (or dropped) using the
delay with feedback.
a: Mode
This parameter switches the pitch shifter operating mode.
With
Slow
, tonal quality will not be changed too much.
With
Fast
, the effect becomes a Pitch Shifter that has a
quick response, but may change the tone.
Medium
is in
between these two. If you do not need to set too much
pitch shift amount, set this parameter to
Slow
. If you wish
to change the pitch significantly, use
Fast
.
b: Pitch Shift [1/2tone], b: Src, b: Amt, c: Fine [cent], c: Amt
The amount of pitch shift will use the value of the “Pitch
Shift” plus the “Fine” value. The amount of modulation
will use the c: Amt value plus d: “Amt.”
Modulation Source is used both for “Pitch Shift” and
“Fine.”
e: Feedback Position, f: Feedback
When “Feedback Position” is set to
Pre
, the pitch shifter
output is again input to the pitch shifter. Therefore, if you
specify a higher value for the Feedback parameter, the
pitch will be raised (or lowered) more and more each time
feedback is repeated.
If “Feedback Position” is set to
Post
, the feedback signal
will not pass through the pitch shifter again. Even if you
specify a higher value for the Feedback parameter, the
pitch-shifted sound will be repeated at the same pitch.
a
Mode
Slow, Medium, Fast
Switches Pitch Shifter mode
☞
b
Pitch Shift [1/2tone]
–24...+24
Sets the pitch shift amount by steps of a semitone
☞
,
Src
Off...Tempo
Selects the modulation source of pitch shift amount
☞
Amt
Sets the modulation amount of pitch shift amount
–24...+24
☞
c
Fine [cent]
Sets the pitch shift amount by steps of a cent
–100...+100cent
☞
,
Amt
Sets the modulation amount of pitch shift amount
–100...+100cent
☞
d
Delay Time [msec]
Sets the delay time
0...1000msec
e
Feedback Position
Switches the feedback connection.
Pre, Post
☞
f
Feedback
Sets the feedback amount
–100...+100
☞
High Damp [%]
Sets the damping amount in the high range
0...100%
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Input Level
Input Level
+
High Damp
Delay
Feedback
Pitch Shifter
Feedback Position
Pre
Post
g
Input Level Dmod [%]
–100...+100
Sets the modulation amount of the input level
☞
Fx:037,
Src
Selects the modulation source for the input level
Off...Tempo
☞
Fx:037
h
Wet/Dry
Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 1
Src
Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 1
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 1
–100...+100
Содержание KD-150
