Kohler KD-150, Руководство пользователя

Страница: 228 / 307

18-3 Effects
Filter/Dynamic
003: Limiter
(Stereo Limiter)
The Limiter regulates the input signal level. It is similar to the
Compressor, except that the Limiter compresses only signals
that exceed the specified level to lower unnecessary peak sig-
nals. The Limiter applies a peaking-type EQ to the trigger sig-
nal (which controls the degree of the Limiter effect), allowing
you to set any band width to be covered. This effect is a stereo
limiter. You can link left and right channels, or use each chan-
nel individually.
a: Envelope Select
When L/R Mix is selected for this parameter, the left and
right channels are linked to control the Limiter using the
mixed signal. If L Only (or R Only ) is selected, the left and
right channels are linked, and the Limiter is controlled via
only the left (or right) channel.
With
L/R individually , the left and right channels control
the Limiter individually.
b: Ratio, c: Threshold [dB], e: Gain Adjust [dB]
This parameter sets the signal compression “Ratio”. Com-
pression is applied only when the signal level exceeds the
“Threshold” value.
Adjust the output level using the “Gain Adjust” parame-
ter, since compression causes the entire level to be
reduced.
d: Attack, d: Release
These parameters set the attack time and release time. A
higher attack time will cause the compression to be
applied slowly.
f: Side PEQ Insert, g: Side PEQ Cutoff [Hz], g: Q, g: Gain
[dB]
These parameters are used to set the EQ applied to the
trigger signal.
The Limiter determines whether the compression is
applied or not, based on the post-EQ trigger signal. Set-
ting the equalizer allows you to set the Limiter to respond
to any frequency band.
f: Trigger Monitor
Setting this parameter On will cause the trigger signal to
be output, instead of the effect sound. Use this parameter
to check the trigger signal with EQ applied.
Usually, set this to
Off .
a
Envelope Select L/R Mix, L Only, R Only, L/R Individually
Selects from linking both channels, controlling only from left channel, only
from the right channel, or controlling each channel individually
☞
b
Ratio 1.0:1...50.0:1, Inf:1
Sets the signal compression ratio
☞
c
Threshold [dB] –40...0dB
Sets the level above which the compressor is applied
☞
d
Attack
Sets the attack time 1...100
☞
Release
Sets the release time 1...100
☞
e
Gain Adjust [dB]
Sets the output gain –Inf, –38...+24dB
☞
,
Src
Selects the modulation source for the output gain Off...Tempo
Amt
Sets the modulation amount of the output gain –63...+63
f
Side PEQ Insert
Toggles between on/off of the trigger signal’s EQ Off, On
☞
Trigger Monitor Off, On
Switches between effect output monitor and trigger signal monitor
☞
g
Side PEQ Cutoff [Hz] 20...12.00kHz
Sets the EQ center frequency for the trigger signal
☞
Q
Sets the EQ bandwidth for the trigger signal 0.5...10.0
Gain [dB]
Sets the EQ gain for the trigger signal –18.0...+18.0dB
h
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 1
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 1
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 1 –100...+100
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Limiter
Limiter
Envelope Select
Gain Adjust
Gain Adjust
Side PEQ
Envelope - Control
Envelope - Control
Trigger Monitor
+
Input Level
Output Level
Threshold
Ratio=1.0 : 1
Ratio=2.0 : 1
Ratio=4.0 : 1
Ration=Inf : 1
Louder
Louder
Time
Level
Threshold
Ratio=Inf : 1
Ratio=2.0 : 1
Ratio=4.0 : 1
Dry
Ratio=1.0 : 1
Limiter - Threshold / Ratio
Threshold
Ratio=Inf : 1
Attack=1
Release=1
Ratio=Inf : 1
Attack=100
Release=100
Dry
Wet
Wet
Release
Attack
Limiter - Attack / Release