Kohler 15/30RES Скачать руководство пользователя страница 9

Страница: 9 / 72

TP-6198 3/15

Safety Precautions and Instructions

Welding on the generator set. Can

cause severe electrical equipment

damage.

Before welding on the

generator set perform the following

steps: (1) Remove the battery cables,

negative (--) lead first. (2) Disconnect

all engine electronic control module

(ECM) connectors. (3) Disconnect all

generator set controller and voltage

regulator circuit board connectors.

(4) Disconnect the engine battery-

charging

alternator

connections.

(5) Attach the weld ground connection

close to the weld location.

Installing

the

battery

charger.

Hazardous

voltage

can

cause

severe injury or death.

ungrounded battery charger may

cause electrical shock. Connect the

battery charger enclosure to the ground

of a permanent wiring system. As an

alternative,

install

equipment

grounding

conductor

with

circuit

conductors and connect it to the

equipment grounding terminal or the

lead on the battery charger. Install the

battery charger as prescribed in the

equipment manual. Install the battery

charger in compliance with local codes

and ordinances.

Testing live electrical circuits.

Hazardous voltage or current can

cause severe injury or death.

Have

trained and qualified personnel take

diagnostic measurements of live

circuits. Use adequately rated test

equipment with electrically insulated

probes and follow the instructions of the

test equipment manufacturer when

performing voltage tests. Observe the

following precautions when performing

voltage tests: (1) Remove all jewelry.

(2) Stand on a dry, approved electrically

insulated mat. (3) Do not touch the

enclosure or components inside the

enclosure. (4) Be prepared for the

system to operate automatically.

(600 volts and under)

High voltage test.

Hazardous

voltage can cause severe injury or

death.

Follow the instructions of the

test equipment manufacturer when

performing high-voltage tests on the

rotor or stator.

An improper test

procedure can damage equipment or

lead to generator set failure.

Connecting the battery and the

battery charger. Hazardous voltage

can cause severe injury or death.

Reconnect

the

battery

correctly,

positive to positive and negative to

negative, to avoid electrical shock and

damage to the battery charger and

battery(ies).

Have

qualified

electrician install the battery(ies).

Short

circuits.

Hazardous

voltage/current can cause severe

injury or death.

Short circuits can

cause bodily injury and/or equipment

damage

Do not contact electrical

connections with tools or jewelry while

making

adjustments

repairs.

Remove all jewelry before servicing the

equipment.

Engine block heater.

Hazardous

voltage can cause severe injury or

death.

The engine block heater can

cause electrical shock. Remove the

engine block heater plug from the

electrical outlet before working on the

block heater electrical connections.

Electrical backfeed to the utility.

Hazardous backfeed voltage can

cause severe injury or death.

Install

a transfer switch in standby power

installations to prevent the connection

of standby and other sources of power.

Electrical backfeed into a utility

electrical system can cause severe

injury or death to utility personnel

working on power lines.

Moving Parts

Airborne particles.

Can cause severe injury or

blindness.

Wear protective goggles and clothing

when using power tools, hand tools,

or compressed air.

WARNING

Servicing the generator set when it

is operating. Exposed moving parts

can cause severe injury or death.

Keep hands, feet, hair, clothing, and

test leads away from the belts and

pulleys when the generator set is

running. Replace guards, screens, and

covers before operating the generator

set.

Heavy Equipment

Unbalanced weight.

Improper lifting can cause severe

injury or death and equipment

damage.

Do not use lifting eyes.

Lift the generator set using lifting bars

inserted through the lifting holes on

the skid.

WARNING

Hot Parts

Hot engine and exhaust system.

Can cause severe injury or death.

Do not work on the generator set until

it cools.

WARNING

Содержание 15/30RES









































































Результаты поиска

Содержание 15/30RES

Отзывы:

Бренды по названию

Популярные бренды

Kohler 15/30RES, Руководство по обслуживанию

Результаты поиска

Содержание 15/30RES

Отзывы:

Бренды по названию

Популярные бренды