Kohler 15/30RES Скачать руководство пользователя страница 41

Страница: 41 / 72

TP-6198 3/15

Section 4 Controller

4.9 Controller Configuration and

Adjustment

This section contains instructions for using the

controller’s password-protected menus to check and

adjust the generator output and controller configuration.

The controller configuration and generator set output

are factory-set and should not require field adjustment

under normal circumstances. Check and adjust the

configuration and/or output in the following cases:

Check and adjust the controller configuration and

generator output after generator set reconnection to a

different voltage.

Check controller configuration when troubleshooting

generator set problems.

Check and adjust the generator set output after

installation if the voltage requires adjustment for a

particular application.

4.9.1

Voltage Adjustments

Hazardous voltage.

Can cause severe injury or death.

Operate the generator set only when

all guards and electrical enclosures

are in place.

Moving parts.

WARNING

Short circuits. Hazardous voltage/current can cause

severe injury or death.

Short circuits can cause bodily injury

and/or equipment damage

Do not contact electrical

connections with tools or jewelry while making adjustments or

repairs. Remove all jewelry before servicing the equipment.

The controller’s adjustment mode allows adjustment of

the output voltage, if necessary. Have adjustments

performed by an authorized distributor/dealer or service

technician.

Note:

A digital voltmeter is required for these

adjustments.

Use a voltmeter to check the output voltage. If the output

voltage is not within specifications, use the ADC

controller to adjust the output voltage while the

generator set is running. The flowcharts in Figure 4-13

and Figure 4-14 outline the adjustment procedures.

Note:

Be sure to save your settings before exiting the

configuration mode.

Voltage changes are lost if they are not saved before the

generator set shuts down. The generator set continues

to run with the new settings until it shuts down but then

reverts to the previous settings at the next startup if the

changes have not been saved.

Pressing the Select button when SAVE is displayed

returns to the first parameter, voltage adjust (1P).

Note:

Refer to the flowcharts in Figure 4-13 and

Figure 4-14 during the voltage adjustment

procedure.

Voltage Adjustment Procedure

1. With the generator set off, connect a digital

multimeter to the output leads or an electrical outlet

on the load side of the generator set. Set the meter

to measure AC voltage.

2. Start the generator set by moving the generator set

master switch to the RUN position.

3. Use the ADC controller to adjust the voltage

(parameter 1P) until the output voltage reaches the

desired value.

See Figure 4-12 for the

approximate change in voltage per step in

parameter 1P.

Measured

Voltage, VAC

Voltage Change per Step, VAC

Coarse Adjust

Fine Adjust

85--132

0.5

180--251

0.7

Figure 4-12

Voltage Adjustment (approximate)

4. Adjust the voltage stability (gain, parameter 2P) to

minimize light flicker.

5. Readjust the voltage, if necessary.

6. Stop the generator set.

Содержание 15/30RES









































































Результаты поиска

Содержание 15/30RES

Отзывы:

Бренды по названию

Популярные бренды

Kohler 15/30RES, Руководство по обслуживанию

Результаты поиска

Содержание 15/30RES

Отзывы:

Бренды по названию

Популярные бренды