Kohler 15/30RES Скачать руководство пользователя страница 19

Страница: 19 / 72

TP-6198 3/15

Section 2 Scheduled Maintenance

Section 2 Scheduled Maintenance

Hazardous voltage.

Will cause severe injury or death.

This equipment must be installed and

serviced

qualified

electrical

personnel.

DANGER

Accidental starting.

Can cause severe injury or death.

Disconnect the battery cables before

working on the generator set.

Remove the negative (--) lead first

when disconnecting the battery.

Reconnect the negative (--) lead last

when reconnecting the battery.

WARNING

Disabling the generator set. Accidental starting can

cause severe injury or death.

Before working on the

generator set or connected equipment, disable the generator

set as follows: (1) Move the generator set master switch to the

OFF position. (2) Disconnect the power to the battery charger.

(3) Remove the battery cables, negative (--) lead first.

Reconnect the negative (--) lead last when reconnecting the

battery. Follow these precautions to prevent starting of the

generator set by an automatic transfer switch, remote

start/stop switch, or engine start command from a remote

computer.

Hazardous voltage.

Can cause severe injury or death.

Operate the generator set only when

all guards and electrical enclosures

are in place.

Moving parts.

WARNING

Hot engine and exhaust system.

Can cause severe injury or death.

Do not work on the generator set until

it cools.

WARNING

Servicing the exhaust system. Hot parts can cause

severe injury or death.

Do not touch hot engine parts. The

engine and exhaust system components become extremely

hot during operation.

Servicing the alternator. Hot parts can cause severe

injury or death.

Avoid touching the alternator field or exciter

armature.

When shorted, the alternator field and exciter

armature become hot enough to cause severe burns.

Risk of fire.

Can cause severe injury or death.

Do not smoke or permit flames or

sparks near fuels or the fuel system.

WARNING

Servicing the fuel system. A flash fire can cause severe

injury or death.

Do not smoke or permit flames or sparks near

the carburetor, fuel line, fuel filter, fuel pump, or other potential

sources of spilled fuels or fuel vapors. Catch fuels in an

approved container when removing the fuel line or carburetor.

Servicing the air cleaner. A sudden backfire can cause

severe injury or death.

Do not operate the generator set with

the air cleaner removed.

Gas fuel leaks. Explosive fuel vapors can cause severe

injury or death.

Fuel leakage can cause an explosion. Check

the LPG vapor or natural gas fuel system for leakage by using

a soap and water solution with the fuel system test pressurized

to 6--8 ounces per square inch (10--14 inches water column).

Do not use a soap solution containing either ammonia or

chlorine because both prevent bubble formation. A successful

test depends on the ability of the solution to bubble.

Содержание 15/30RES









































































Результаты поиска

Содержание 15/30RES

Отзывы:

Бренды по названию

Популярные бренды

Kohler 15/30RES, Руководство по обслуживанию

Результаты поиска

Содержание 15/30RES

Отзывы:

Бренды по названию

Популярные бренды