Kohler 15/30RES Скачать руководство пользователя страница 45

Страница: 45 / 72

TP-6198 3/15

Section 4 Controller

The controller will automatically exit the configuration

mode without saving any changes after about 1 minute

if no buttons are pressed. Start the configuration

procedure over again from the beginning if the controller

exits the configuration mode before the settings have

been saved.

Follow the instructions in Figure 4-17 to enter the

configuration mode while the engine is not running and

then step through the following parameters. Use the up

(



) and down (



) arrow buttons to select the appropriate

setting for the application.

Voltage/frequency setting (Uu).

Select the system

voltage and frequency from the table in Figure 4-15. For

system voltages not listed in the table, select the setting

closest to the system voltage and then adjust the output

voltage to the desired level using the instructions in

Section 4.9.1.

Note:

This parameter sets the nominal system voltage

and frequency. To adjust the output (measured)

voltage, see Section 4.9.

Unit configuration (Uc).

This parameter sets the

generator set type: marine, standby, or mobile.

Engine configuration (Ec).

The engine configuration

must match the generator set engine type.

Advanced configuration mode (Adnc).

The data

input types, battery voltage, and communications

setting can be changed in the advanced configuration

mode. Press the up arrow button when

Adnc

displayed to enter the advanced configuration mode.

Engine data input types (Ed).

This setting defines the

type of senders used on the generator set engine. Use

Ed01 for the 15/30RYG/RES.

The remote digital gauge requires the optional analog oil

pressure sender. Install the optional sender and change

the Ed parameter to Ed02.

Battery voltage (Bt).

This setting toggles between 12

and 24 VDC for the engine starting battery voltage.

Communications setting (Cn).

This setting allows the

user to set the controller for communication with

optional meters. The 15/30RYG/RES is factory-set for

no CAN communications, Cn00. Change this setting to

Cn01 if the optional Remote Digital Gauge is used.

Note:

Be sure to save your settings before exiting the

configuration mode. The controller reverts to the

last saved settings when the master switch is

moved to the OFF/RESET position.

Содержание 15/30RES









































































Результаты поиска

Содержание 15/30RES

Отзывы:

Бренды по названию

Популярные бренды

Kohler 15/30RES, Руководство по обслуживанию

Результаты поиска

Содержание 15/30RES

Отзывы:

Бренды по названию

Популярные бренды