manualshive.com logo in svg

Kohler 15/30RES, Руководство по обслуживанию

Поделиться
Скачать
Kohler 15/30RES Скачать руководство пользователя страница 43

TP-6198 3/15

43

Section 4 Controller

Display : *

Continued from Figure 4-13:

*

X

in the examples above denotes any number from 0 to 9. The actual values

may vary from model-to-model.

S A V E

To enter SAVE mode.

Note: Be sure to save your settings before exiting the configuration mode. The controller reverts to

the last

saved

settings when the master switch is moved to the OFF/RESET position.

To save changes.

To discard changes without saving.

or

S A V E

Y E S

Now move the master switch to OFF/RESET.

n o

There are 3 options when the display says SAVE:

Press:

or

To return to the first parameter, coarse voltage adjustment, to check

or change settings before saving. See Figure 4-13.

“Yes”or “no” flashes when the up or down arrow is pressed and then the

controller exits the configuration mode. The display returns to the

runtime hours.

1 P

x x x x

x x

Figure 4-14

Output Voltage Adjustments, Continued

Содержание 15/30RES









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды