Antenna
®
Telescope
™
Antenna
®
Telescope
™
Installation Instructions
October 2018
63
Telescope 120˚ Triad with Beam
(with or without Dual Utility Trays)
INSTALL THE HEIGHT ADJUSTMENT
ELECTRICAL COMPONENTS:
25. For each station, decide if the Handset
Control Switch (J) will be on the outer
left or outer right side of the station.
26. Plug the handset cable into a housing outlet
on the chosen side. Connect one end of a
LONG iDrive Cable into the second outlet on
that side and the other end into an opposite
housing outlet on the triangle structure.
Continue the connection with a SHORT iDrive
Cable to jump power from the second outlet
on that side of the housing to an outlet on
the opposite side of that same housing. Link
another LONG iDrive Cable, connecting from
the second outlet on the triangle structure
housing to an outlet on the other end of the
station. (see User Manual for cable diagram).
27. Insert the Power Supply plug into the
remaining outlet on the non-handset side.
Insert the power cord into the power
supply and position the power supply on
the nearest Transformer Shelf (F) so that
the green LED is visible from below.
PERFORM A RESET FOR THE TRIO
OF COLUMNS IN EACH STATION:
28. Plug the power supply into a temporary
power source. Ensure the green
LED on the power supply lights.
29. Apply approximately 100 lbs. of weight to the
rails. Press and hold both UP and DOWN
buttons for ten seconds. After releasing the
buttons, press and hold the DOWN BUTTON
until all three columns bottom out. Press the
UP button and the station will be ready to
perform normally. Remove the weight. Run
the station all the way up and down again to
ensure there are no issues with the columns.
Repeat the procedure above for
the other two stations.
ENSURE COLUMNS ARE PLUMB
THROUGHOUT RANGE OF TRAVEL:
To avoid issues that may arise if columns are
forced out of alignment during usage, a thorough
check is required at this point in the installation. If
adjustment is required, it is best to adjust at the
mid-column cradles, if possible. Rail adjustments
made here are hidden, allowing the correct outset
of the rail caps at the outer ends. If additional
rail adjustment is required, then make those
adjustments at the outer cradles. Free movement of
the columns takes priority over the rail cap outset.
30. Using a laser level, or similar, ensure that
the upper column elements are in line and
paralleling the lower column tube, made plumb
at Step 21. Make rail adjustments, described
above, as needed, to retain column tube
alignment throughout the range of travel.
ATTACH CONNECTOR LINKS/ CONNECT
TABLES (WHERE APPLICABLE):
31. Attach (2) Dovetail Linking Brackets
(BB) to the outside of the outer crossbar
using (2) 1/4 -20 x ¾" flat head machine
screws (CC) per bracket. The base of
the “L” should be oriented downward.
32. Prepare the Connector Link (EE) for the Wire
Hanger (DD) by loosely screwing (2) ¼-20 x
3/4" button head machine screws (V) into the
underside of the connector link. Leave a gap
of about ³/
16
" beneath the head of the screws.
Place the wire hanger over the heads of the
screws and slide to engage the keyhole slots.
NOTE:
Repeat the above two steps for
the outer crossbar and Connector Link
of the connecting table assembly.
33. To connect tables, position both table
assemblies side by side so the prepared
connector links (EE) can be slid down onto
the linking brackets (BB) previously attached
to the crossbars. Fasten the connector links
to the linking brackets with a ¼ -20 x ¾" flat
head machine screw (CC) at each end.
INSTALL TOPS:
34. Lay tops on base assembly. Place a Spacer (Q)
between the top of each rail and the underside
of the top, centered on the width of the top.
Spacers are attached to the top using (1) #12 X
¾" flat head black wood screw (R) per spacer.
NOTE:
Back to back tops are to be 6" apart.
35. Attach tops using (4) #14 x 1" flat head wood
screws (S) per outer Horizontal Rail Cradle (C),
and (2) #14 x 1" flat head wood screws (S) per
center cradle cavity in 120 Degree Center Rail
Cradle (GG/HH).
NOTE:
Several screw hole locations are directly
above the crossbars, so it is convenient to
raise the station to make room for the power
driver.
NOTE:
Do NOT force columns out of alignment
to align pilot holes with cradle holes. If
worksurface pilot holes do not align with
cradle holes, drill new pilot holes, as needed.
Use a drill bit depth stop to prevent drilling
through the top surface of the worktop.
AFFIX HANDSET:
36. Using (2) #6 x
5
/
8
" wood screws (K) mount
the Handset Control Switch (J) to the
underside of the worktop, at the front edge.
INSTALL POWER STRIP ACCESSORY
(WHERE APPLICABLE):
See Power Strip Installation Instructions.
INSTALL CLEAT PLATE & CLEAT PLATE COVER
ACCESSORIES (WHERE APPLICABLE):
See Cleat Plate and Cleat Plate
Cover Installation Instructions.
INSTALL Z MANAGER ACCESSORY
(WHERE APPLICABLE):
See Z-Manager Installation Instructions.