Antenna
®
Telescope
™
Antenna
®
Telescope
™
Installation Instructions
October 2018
58
Telescope 120˚ Triad with Beam
(with or without Dual Utility Trays)
4. Determine requirement for Starter Crossbars
(G) and/or Mid Crossbars (H) for the three pairs
of outer legs, based on table application.
NOTE:
The Starter Crossbars will have holes
on the inside of them to accept the legs and
beam (and utility trays, where specified). Mid
Crossbars will have holes on both sides; i.e.,
the inside has holes for the legs and beam
(and utility trays where specified), and the
outside has holes for linking brackets.
5. For each outer crossbar (G/H), place a
Pull Block (I) into each end, and attach
securely with (2)
5
/
16
-18 x ¾" flat head
hex machine screws (N) per pull block
in the underside of the crossbar.head
Phillips machine screws (M) per cover.
6. Ensure the three crossbars are oriented right
side up and so the insides are facing one
another (towards the center of the triad).
Attach a Center Beam Mounting Plate (U) to
the inside of each crossbar, using (4) ¼-20 x
¾" button head machine screws (V) per plate.
Insert M8-1.25 x 8mm hex set screws (W)
into both tabs on the sides of all three plates
(U), such that the hex recesses are outward.
CONNECT CROSSBARS AND BEAMS TO
LEGS, CREATING THREE SUB-ASSEMBLIES:
7. For each outer leg set, turn a crossbar
assembly and the corresponding (2) leg
assemblies upside down, and connect the
leg assemblies to the crossbars by sliding
the ends of the crossbars onto the welded
column brackets. Join with (2)
5
/
16
-18 x ¾"
flat head hex machine screws (N), loosely,
into each bracket. Do not tighten at this
time. Allow the screws to seat in the counter
sinks and perform the next steps.
8. Place a washer (P) on a
5
/
16
-18 x 2" button
head hex machine screw (O) and insert it
into the bottom of a crossbar at an angle to
penetrate the pull block and thread into the
column bracket. Torque screw to 150 in. lbs.
(17 Nm). Repeat for the five other crossbar
ends. Tighten the (6) pairs of flat head machine
screws previously left loose.
Turn each assembly right side up
to perform the next step.
9. Ensure the Center Beams are oriented
correctly (the top of the beam has a slot within
a deep recess, the bottom of the beam has a
slot within a wide recess). Mate a beam to the
previously attached mounting plate (U), and
secure by tightening the set screws (W) with a
4mm hex driver.
Repeat for the other two outer leg sets.
Outer Leg/ Crossbar/ Beam Sub-Assembly,
Steps 4-9
Step 4
Outer Crossbar (G/H)
Step 5
Pull Block (I)
5
/
16
-18 x ¾" Flat Head Hex
Machine Screws (N)
Step 6
Center Beam Mounting Plate (U)
¼-20 x ¾" Button Head
Machine Screw (V)
Step 6 & 9
M8-1.25 x 8mm Hex Set Screws (W)
Step 7
Step 8
5
/
16
-18 x 2" Button Head
Hex Machine Screw (O)
5
/
16
-18 x ¾" Flat Head Hex
Machine Screws (N)
Washer (P)
Completed Outer Leg/ Crossbar/ Beam Sub-Assembly
Center Beam
Outer Crossbar
Outer Legs
