background image

Antenna

®

 Telescope

Antenna

®

 Telescope

 Installation Instructions

October 2018

8

Telescope Dual Table Bases without Beam  

and  Dual  Utility  Trays    -  Standard  Electric                                                                      

4.   Place a Pull Block (I) into each end of the (2) 

Beamless Trayless Starter Crossbars (G), 
and attach securely with (2) 5/16-18 x 3/4" 
flat head hex machine screws (N) per pull 
block in the underside of the crossbar.

CONNECT CROSSBARS TO LEGS:

5.   With the legs and crossbars upside down, 

connect the leg assemblies to the crossbars 
by sliding the ends of the crossbars onto the 
welded column brackets, and joining with (2) 
5/16-18 x 3/4" flat head hex machine screws 
(N), loosely, into each bracket. Do not tighten 
at this time. Allow the screws to seat in the 
counter sinks and perform the next step.

6.   Place a washer (P) on a 5/16-18 x 2" button 

head hex machine screw (O) and insert it into 
the bottom of the crossbar at an angle to 
penetrate the pull block and thread into the 
column bracket. Torque screw to 150 in. lbs. (17 
Nm). Repeat for the three other crossbar ends. 
Tighten the (4) pairs of flat head machine screws 
previously left loose. Turn asembly right side up.

Exploded Table Base Without 

Beam Assembly, Steps 4-6

Pull Block (I) 

5/16-18 x  3/4" Flat Head 
Hex Machine Screw (N) 

5/16-18 x 3/4" Flat Head 
Hex Machine Screw (N) 

Beamless 
Trayless 
Crossbar (G)

Washer (P)

5/16-18 x 2" 
Button Head Hex 
Machine Screw (O)

Step 4

Steps 5 & 6

Содержание Antenna Telescope




















































































































Отзывы: