Knoll Antenna Telescope Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 115

background image

Antenna

®

Telescope

™

Antenna

®

Telescope

™

Installation Instructions

October 2018

16

Telescope Dual Table Bases with Beam (with or

without Dual Utility Trays) - Standard Electric

4. Determine requirement for Starter

Crossbars (G) and/or Mid Crossbars
(H), based on table application.

Note

: The Starter Crossbars will have holes

on the inside of them to accept the legs and
beam (and utility trays, where specified). Mid
Crossbars will have holes on both sides; i.e.,
the inside has holes for the legs and beam
(and utility trays where specified), and the
outside has holes for linking brackets.

5. For each required crossbar (G/H), place a Pull

Block (I) into each end, and attach securely with
(2) 5/16-18 x 3/4" flat head hex machine screws (N)
per pull block in the underside of the crossbar.

CONNECT BEAM TO CROSSBARS

6. Ensure the crossbars are oriented right side

up and so the insides are facing one another.
Attach a Center Beam Mounting Plate (U) to
the inside of each crossbar, using (4) 1/4-20
x 3/4" button head machine screws (V) per
plate. Insert M8-1 1/4 x 8mm hex set screws
(W) into both tabs on the sides of both plates
(U), such that the hex recesses are outward.

7. Ensure the Center Beam is oriented correctly

(the top of the beam has a slot within a deep
recess, the bottom of the beam has a slot
within a wide recess), mate the beam to one
of the mounting plates (U), and secure by
tightening the set screws (W) with a 4mm
hex driver. Repeat for the other end.

8. Turn the large beam/crossbar “I" assembly

upside down. Position the (4) legs upside
down as well, and in their relative positions
at the ends of the crossbars.

CONNECT CROSSBARS TO LEGS

9. With the legs upside down, connect the leg

assemblies to the crossbars by sliding the ends of
the crossbars onto the welded column brackets,
and joining with (2) 5/16-18 x 3/4" flat head hex
machine screws (N), loosely, into each bracket. Do
not tighten at this time. Allow the screws to seat
in the counter sinks and perform the next steps.

10. Place a washer (P) on a 5/16-18 x 2" button

head hex machine screw (O) and insert it into the
bottom of the crossbar at an angle to penetrate
the pull block and thread into the column bracket.
Torque screw to 150 in. lbs. (17 Nm). Repeat
for the three other crossbar ends. Tighten the
(4) pairs of flat head machine screws previously
left loose. Turn assembly right side up.

Exploded Table Base With Beam and

Dual Utility Trays Assembly, Steps 4-10

Pull Block (I)

Center Beam

Center Beam

M8-1 1/4 x 8mm
Hex Set Screw (W)

1/4-20 x 3/4" Button

Head Machine

Screw (V)
Center Beam
Mounting Plate (U)

Starter or Mid
Crossbar (G/H)

Starter Crossbar (G)
or Mid Crossbar (H)

5/16-18 x 3/4"
Flat Head
Hex Machine
Screw (N)

5/16-18 x 2" Button Head
Hex Machine Screw (O)

Washer (P)

Starter

Crossbar (G)

5/16-18 x 3/4"
Flat Head
Hex Machine
Screw (N)

Step 5

Connecting Beam to

Crossbar Detail, Steps 6 & 7

Steps 9 & 10

«
...
14
15
16
17
18
...
»

Содержание Antenna Telescope




















































































































Отзывы:

Нет отзывов

Похожие инструкции для Antenna Telescope

Бренд: calligaris Страницы: 2

Бренд: NABBI Страницы: 12

Бренд: Gautier Страницы: 16

Бренд: Allen + Roth Страницы: 24

Бренд: Naterial Страницы: 52

Бренд: Forte Страницы: 20

ARC COFFEE TABLE

Бренд: Sage Living Home & Decor Страницы: 2

Бренд: IKEA Страницы: 12

Бренд: Coaster Страницы: 4

Бренд: Tech Craft Страницы: 6

Motion Sync Chair Armrest

Бренд: OLG Страницы: 4

Бренд: Laura Ashley Страницы: 4

Бренд: Nacon Страницы: 8

Бренд: Tee-Zed Страницы: 2

Deluxe Coconino Wicker Chair

Бренд: Patio Sense Страницы: 6

Busetti Garuti Redaelli Buddy 218

Бренд: Pedrali Страницы: 2

Martti 009000244

Бренд: YOTRIO Страницы: 11

Бренд: Hanover Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды