Knoll Antenna Telescope Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 115

background image

Antenna

®

Telescope

™

Antenna

®

Telescope

™

Installation Instructions

October 2018

19

Telescope Dual Table Bases with Beam (with or

without Dual Utility Trays) - Standard Electric

ATTACH CONNECTOR LINKS/ CONNECT

TABLES (WHERE APPLICABLE)

23. Attach (2) Dovetail Linking Brackets (BB) to

the outside of the crossbar using (2) 1/4 -20 x
3/4" flat head machine screws (CC). The base
of the “L" should be oriented downward.

24. Prepare the Connector Link (EE) for the Wire

Hanger (DD) by loosely screwing (2) 1/4-20 x
3/4" button head machine screws (V) into the
underside of the connector link. Leave a gap of
about 3/16" beneath the head of the screws.
Place the wire hanger over the heads of the
screws and slide to engage the keyhole slots.

25. To connect tables, position both table assemblies

side by side so the prepared connector links (EE)
can be slid down onto the linking brackets (BB)
previously attached to the crossbars. Fasten
the connector links to the linking brackets with
a 1/4 -20 x 3/4" flat head machine screw (CC).

LEVEL TABLES

26. Place the tables in their final positions and level

by extending the leveling glides as needed.

27. When levelers are extended more than

1/2", install the Helical Glide Shroud. See
Helical Glide Installation Instructions.

INSTALL TOPS

28. Lay tops on base assembly. Place a Spacer (Q)

between the top of each rail and the underside
of the top, centered on the width of the top.
Spacers are attached to the top using (1) #12 X
3/4" flat head black wood screw (R) per spacer.

Note

: Back to back tops are to be 6" apart.

29. Attach tops using (4) #14 x 1" flat head

wood screws (S) per cradle.

Note

: Several screw hole locations are directly

above the crossbars, so it is convenient to raise
the station to make room for the power driver.

AFFIX HANDSET

Note

: If a return is to be attached, skip

this step and follow Telescope Return
Base Installation Instructions.

30. Using (2) #6 x 5/8" wood screws (K) mount the

Handset Control Switch (J) to the underside
of the worktop, at the front edge.

ATTACH RETURNS (WHERE APPLICABLE)

See Telescope Return Base Installation Instructions.

INSTALL POWER STRIP ACCESSORY

(WHERE APPLICABLE)

See Power Strip Installation Instructions.

INSTALL CLEAT PLATE & CLEAT PLATE COVER

ACCESSORIES (WHERE APPLICABLE)

See Cleat Plate and Cleat Plate Cover
Installation Instructions.

INSTALL Z-MANAGER ACCESSORY (WHERE

APPLICABLE)

See Z-Manager Installation Instructions.

Exploded Table Base with Beam

Assembly, Steps 23-30

Attaching Connector Links

Detail, Steps 23-25

Mid Crossbar (H)

Worksurface Tops

Dovetail
Linking
Bracket
(BB)

#14 x 1" Flat
Head Wood
Screws (S)

Handset
Control Switch (J)

Spacer (Q)

1/4 - 20 x 3/4"
Flat Head
Machine
Screws (CC)

#6 x 5/8" Wood
Screws (K)

#12 X 3/4" Flat Head
Black Wood Screw (R)

Connector
Link (EE)

Wire Hanger
(DD)

1/4-20 x 3/4"
Button Head
Machine
Screws (V)

«
...
17
18
19
20
21
...
»

Содержание Antenna Telescope




















































































































Отзывы:

Нет отзывов

Похожие инструкции для Antenna Telescope

Бренд: paladin Страницы: 3

Бренд: WA Library Supplies Страницы: 2

Бренд: VEDUM Страницы: 4

Бренд: VEDUM Страницы: 5

New Charterhouse 6028

Бренд: Aspace Страницы: 2

OBRA SIDEBOARD BZ-1060-20

Бренд: Moe's Страницы: 2

0-65857-20921-1

Бренд: Dorel Living Страницы: 30

Бренд: Woodard Страницы: 2

Бренд: Ofs Страницы: 4

Бренд: Homelegance Страницы: 3

Safco Apprentice II 6689

Бренд: LDI Страницы: 2

Бренд: Bestar Страницы: 16

Бренд: Euro Style Страницы: 6

Бренд: Rauch Страницы: 9

Бренд: RightAngle Страницы: 2

Бренд: Safavieh Страницы: 4

Stretto 54 03 27 Series

Бренд: Quax Страницы: 41

Mainstays Moss Falls MSD128059664017

Бренд: YOTRIO Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды