Knick SensoGate WA131MH Скачать руководство пользователя

Страница: 36 / 60

SensoGate WA131MH

6.3.7 Calibration Chamber: Installation

Note:

ZU0754 service set or ZU0740 service set are required to install the calibration chamber.

➜

Tools, p. 47

Note:

To ensure correct assembly of the O-rings and the scraper ring, use the accessory tools ZU0746

and ZU0747. The procedure for handling the accessory tools is described in the relevant documenta-
tion.

➜

Tools, p. 47

01.

Check the O-rings and scraper ring for damage; replace the O-rings and scraper ring if necessary.

➜

Gasket Sets, p. 40

02.

Connect the top

(1)

and the bottom

(2)

of the calibration chamber and screw together finger

tight.

03.

Position the pliers

(4)

and use the face pin spanner wrench

(3)

to screw the calibration chamber

together.

Note:

Securing the calibration chamber with the two screws is not possible until the top and bottom

parts have been firmly screwed together (to the hard stop).

04.

Tighten the screws

(5)

with a screwdriver of type TX25 .

6.3.8 Knick Repair Service

The Knick Repair Service offers professional corrective maintenance on the SensoGate WA131MH to
the original quality. Upon request, a replacement unit can be obtained for the period of the repair.

Further information can be found at www.knick.de.

Содержание SensoGate WA131MH





























































Результаты поиска

Содержание SensoGate WA131MH

Отзывы:

Похожие инструкции для SensoGate WA131MH

Бренды по названию

Популярные бренды

Knick SensoGate WA131MH, Руководство пользователя

Результаты поиска

Содержание SensoGate WA131MH

Отзывы:

Похожие инструкции для SensoGate WA131MH

Бренды по названию

Популярные бренды