Knick SensoGate WA131MH Скачать руководство пользователя

Страница: 37 / 60

SensoGate WA131MH

7 Troubleshooting

7.1 Malfunction States

Malfunction state

Possible causes

Remedy

Process medium escapes
from the leakage bore

Leaking due to damaged O-rings

Replace damaged O-rings

➜

Gasket Sets, p. 40

The safety lock button
cannot be depressed

Sensor mounted incorrectly

Mount sensor correctly

➜

Installing and Removing a Sensor, p. 25

O-ring or compression ring of
solid-electrolyte sensor not
present or not correctly posi-
tioned

Correctly install O-ring or compression ring of
solid-electrolyte sensor

➜

Installing and Removing a Sensor, p. 25

Corrosion or contamination by
process medium

Perform emergency release

➜

Retractable Fitting: Emergency Release, p. 38

Clean the SensoGate WA131MH or send it to
Knick for corrective maintenance

➜

Knick Repair Service, p. 36

"Immersion lock without
mounted sensor" safe-
guard not working

Corrosion or clogging by pene-
trated process medium

Send SensoGate WA131MH to Knick for repair

➜

Knick Repair Service, p. 36

Emergency release performed
(set screw screwed in)

Reset emergency release

➜

Retractable Fitting: Emergency Release, p. 38

Sensor glass shattered

Mechanical impact on the sensor
glass (e.g. by process medium)

Replace faulty sensor

➜

Installing and Removing a Sensor, p. 25

Remove any glass splinters from the SensoGate
WA131MH. Check immersion tube seal and
replace if necessary

➜

Gasket Sets, p. 40

No or wrong measured
value displayed

Sensor may be faulty

Replace the sensor.

➜

Installing and Removing a Sensor, p. 25

Sensor cable damaged or plug
connection faulty

Fasten plug connection or replace damaged
sensor cable

➜

Installing and Removing a Sensor, p. 25

Содержание SensoGate WA131MH





























































Результаты поиска

Содержание SensoGate WA131MH

Отзывы:

Похожие инструкции для SensoGate WA131MH

Бренды по названию

Популярные бренды

Knick SensoGate WA131MH, Руководство пользователя

Результаты поиска

Содержание SensoGate WA131MH

Отзывы:

Похожие инструкции для SensoGate WA131MH

Бренды по названию

Популярные бренды