background image

 

                                                                                 5                   

 

 

 

-

  If the control knob is turned very quickly from HIGH to LOW, the flame may 

go out, particularly if the burner is cold. If this occurs, turn the knob to the 
OFF position, wait several seconds and relight the burner. Refer to LOW 
SETTING VALVE ADJUSTMENT chapter to adjust LOW setting, if 
needed. 

-

  The flame should not extend beyond the edge of the pan. 

 
 

MAINTENANCE

  

 
CLEANING SAFETY 
 

Turn off all controls and wait for appliance parts to cool before touching or 
cleaning them. Do not touch the burner grates or surrounding areas until they 
have had sufficient time to cool. 
Clean appliance with caution. Use care to avoid steam burns if a wet sponge 
or cloth is used to wipe spills on a hot surface. Some cleaners can produce 
noxious fumes if applied to a hot surface. 

 

BURNERS 

 

Take off the removable parts and put them for 10 minutes in soapy 
warm water. Eventual stubborn soils can be removed by using a 
nonabrasive pad or a plastic scouring pad, then rinse making sure that 
all openings are free of dirt, fig. 04. 

 
 
 
 
SURFACE CLEANING 
 

This is easily done using a damp cloth and a non-abrasive detergent, 
wipe using a soft dry cloth. For stainless steel parts with stubborn soils. Use 
only plastic scrubbing pad or a sponge with vinegar and warm water. 
 
Because of many new cleaning products introduced in the marketplace each 
year, it is not possible to list all products that can be safely be used to clean 
this appliance. Read carefully the cleaner manufacture’s instructions to be 
sure the cleaner can be safely used on this appliance. Although, to determine 
if a cleaning product is safe, test a small inconspicuous area using a very light 
pressure to see if the surface may scratch or discolour. This 

LV

particular

O\

 

important for porcelain enamel, highly polished, shiny, painted or plastic 
surfaces.  

 

Содержание KCGCT6010





























Отзывы: