Kingspan AeroMax Plus KHP0038, Руководство по установке и обслуживанию

Страница: 49 / 72

49
Option 71 - Random start rules (24V/230 Volt models only)
This enables a random start on pow-
er-up following a power cut to reduce
load on the electrical network.
Random delay is in the range of 2 - 90
seconds. Press + until Option 71 is
EJTQMBZFEVTF7BOEȣUPTFMFDU
required setting.
Setting 0 Disabled (factory setting)
Setting 1 Enabled
Option 72 - Owner site reference number
This enables multi-site owners
to store a site reference
number in the thermostat.
Press + until Option 72 is
EJTQMBZFEVTF7BOEȣUP
select required setting.
Setting Any value between 00 and 99 can be set
'BDUPSZTFUUJOHJT
Option 73 - Owner thermostat reference number
This enables site owners to store a
thermostat reference umber in the
thermostat. Press + until Option 73
JTEJTQMBZFEVTF7BOEȣUPTFMFDU
required setting.
Setting Any value between 000 and 999 can be set
'BDUPSZTFUUJOHJT
Option 74 - Date format for calendar clock
This allows date format to be
chosen. Press + until Option
JTEJTQMBZFEVTF7BOEȣUP
select required setting.
Setting 0 &VSPQFBOGPSNBU EENNZZ 'BDUPSZTFUUJOH
Setting 1 North American format (mm/dd/yy)
Option 81 - Thermostat calibration bias
This allows the thermostat calibration
UPCFCJBTFECZVQUPœ¡$1SFTT
+ until Option 81 is displayed, use V
BOEȣUPTFMFDUSFRVJSFETFUUJOH
Setting "OZWBMVFCFUXFFOœJO¡$TUFQT 'BDUPSZ
setting is 0°C)
Option 90 - Defi ne remote sensor type, “A” models only
This allows type of remote
sensor input type to be defi
ned. Press + until Option 90
JTEJTQMBZFEVTF7BOEȣUP
select required setting.
Setting 0 /PSFNPUFTFOTPSöUUFE 'BDUPSZTFUUJOH
Setting 1 Remote room or duct sensor fitted, internal sen-
sor disabled,
Setting 2 Remote limit sensor fitted, refer to option 93 to
defi ne set-point
Setting 3 Configured as digital input for window, card
reader or teleswitch, refer to option 94 to define
o/c or s/c.
Setting 4 4 hours
Option 93 - Set limit sensor set-point, “A” models only,
(option 90 set to 2)
This allows the thermostat limit sen-
sor to be set, typical application is fl
oor heating. Press + until Option 93 is
EJTQMBZFEVTF7BOEȣUPTFMFDU
required setting. If the temperature
sensed by the limit sensor exceeds
the limit setting the output will be
turned off until the temperature
IBTESPQQFECZ¡$i'wXJMMøBTI
in the displaywhile the output is
disabled.
Setting "OZWBMVFCFUXFFO¡$ 'BDUPSZTFUUJOH
is 27°C)
Option 94 - Confi gure digital input switch type, “A” models
only, (option 90 set to 3)
This allows switch type of
digital input to be confi gured.
Press + until Option 94 is dis-
QMBZFEVTF7BOEȣUPTFMFDU
required setting.
Setting 0 Contacts NC, open circuit contact to force unit
into thermostat mode, short circuit contacts to
return to normal operation
Setting 1 Contacts NO, short circuit contacts to force unit
into thermostat mode, open circuit contacts to
SFUVSOUPOPSNBMPQFSBUJPO 'BDUPSZTFUUJOH
Programable room stat