Keysight N6705 Скачать руководство пользователя | Manualshive

Страница: 58 / 135

background image

3 Calibration

58

Model N6705 Service Guide

Low Range Current Measurement

Step 1. Connect only the current measurement terminals of the Keysight 3458A

to the output terminals.

Step 2. Select the low-current measurement range. The value to program a

range must be the maximum current of the range. This example selects
the 100 mA range of output 1.

Front Panel:

SCPI Command:

From the Calibration menu, select
Current, Low Range Measurement.
Then select Start.

CAL:CURR:MEAS 0.1

, (@1)

Step 3. Select the first current calibration point. For models N6761A and N6762A

only, wait a minimum of 5 minutes for the internal temperature to
stabilize.

Front Panel:

SCPI Command:

The first calibration point is automatically
selected. The ammeter should be connected.
Wait 5 minutes for models N6761A and
N6762A. Select Next. “Enter measured
current” should be displayed.

CAL:LEV P1

Step 4. Measure the current with the Keysight 3458A and enter the value.

Front Panel:

SCPI Command:

Enter the value from the external DMM into
the data field and then select Next. If
calibration is complete, select Close.

CAL:DATA <data>
*OPC?

Steps 5 and 6 only apply to models N6761A and N6762A.

Step 5. Disconnect the Keysight 3458A from the output terminals. Then select

the second current calibration point.

Front Panel:

SCPI Command:

The second calibration point is automatically
selected. “Disconnect Meter” should be
displayed. Select Next when done.

CAL:LEV P2

Step 6. Wait a minimum of 5 minutes for the internal temperature to stabilize.

Then select the third current calibration point.

Front Panel:

SCPI Command:

The third calibration point is automatically
selected. “Wait 5 minutes, press Next” should
be displayed. Wait 5 minutes and select Next.
Then select Close.

CAL:LEV P3
*OPC?

«
...
56
57
58
59
60
...
»

Содержание N6705








































































































































Отзывы:

Нет отзывов

Похожие инструкции для N6705

Бренд: ECC X-RAY Страницы: 14

Бренд: Kane Страницы: 19

Бренд: Bamo Страницы: 8

Бренд: Campbell Страницы: 22

Бренд: Campbell Страницы: 32

Бренд: Campbell Страницы: 40

CR3000 Micrologger

Бренд: Campbell Страницы: 12

Бренд: R.M. Young Страницы: 8

Бренд: Campbell Страницы: 21

Бренд: Xylem Страницы: 24

Бренд: Waltron Страницы: 11

Бренд: Labom Страницы: 6

Бренд: Labom Страницы: 5

Бренд: Kawai Страницы: 22

Concert Performer CP3

Бренд: Kawai Страницы: 40

Бренд: Kawai Страницы: 36

Бренд: Kawai Страницы: 148

Бренд: Kawai Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды