manualshive.com logo in svg

Keysight N6705, Руководство по обслуживанию

Поделиться
Скачать
Keysight N6705 Скачать руководство пользователя страница 18

2    Performance Verification 

18 

Model N6705 Service Guide 

Constant Current Tests 

NOTE

 

Test each output channel individually. Refer to the appropriate test 
record form for the instrument settings of the model you are checking. 

Current Programming and Readback Accuracy 

Test category = performance, calibration 

This test verifies that the current programming and measurement 
functions are within specifications.  

1

 

Turn off the DC Power Analyzer and connect the current shunt 
directly across the output terminals. Connect the DMM directly 
across the current shunt (see Test Setup B). Note that the electronic 
load is not used in this portion of the test. 

2

 

Turn on the DC Power Analyzer and program the instrument settings 
as described in the test record form under “Current Programming & 
Readback, Min Current”. The output status should be “CC”, and the 
output voltage should be close to zero. 

3

 

Divide the voltage drop (DMM reading) across the current shunt by 
the shunt resistance to convert to amps and record this value (Iout). 
Also, record the current measured over the interface. The readings 
should be within the limits specified in the test record form for the 
appropriate model under “Current Programming & Readback, 
Minimum Current”. 

4

 

Program the instrument settings as described in the test record form 
under “Current Programming & Readback, High Current”. 

5

 

Divide the voltage drop (DMM reading) across the current shunt by 
the shunt resistance to convert to amps and record this value (Iout). 
Also, record the current reading measured over the interface. The 
readings should be within the limits specified in the test record form 
for the appropriate model under “Current Programming & Readback, 
High Current”. 

6

 

For models N6761A and N6762A only.

 Connect the Keysight 3458A 

directly across the output (see Test Setup D without the resistor). Set 
the Keysight 3458A to the 100 mA range (no autoranging). Set both 
the current programming and the current measurement functions to 
the low range. Set the instrument as described under “Current 
Programming & Readback, Low Current”. Record the current reading 
of the 3458A. Also, record the current reading measured over the 
interface. The readings should be within the limits specified under 
“Current Programming & Readback, Low Range”. 

7

 

For models N6761A and N6762A with option 2UA only.

 Connect the 

Keysight 3458A and a 20k resistor to the output (see Test Setup D). 
Set the Keysight 3458A to measure current using the 1 mA range. 
Set the current measurement to the 200 µA range. Set the 
instrument as described in the test record form under “Current 
Readback, 200 µA Current”. Record the current reading of the 

Содержание N6705








































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды