Keysight N6705 Скачать руководство пользователя страница 64

Страница: 64 / 135

3 Calibration

Model N6705 Service Guide

Step 4. Select the second voltage calibration point.

Front Panel:

SCPI Command:

The second calibration point is automatically
selected. “Enter P2 measured data” should
be displayed.

CAL:LEV P2
*OPC?

Step 5. Measure the output voltage with the DMM and enter the data.

Front Panel:

SCPI Command:

Enter the value from the external DMM into
the data field and then select Next. If
calibration is complete, select Close.

CAL:DATA <data>

Step 6 only applies to models N6781A and N6782A.

Step 6. Repeat steps 1 through 5 for the 600 mV range.

Steps 7 through 9 only apply to model N6784A.

Step 7. Select the third voltage calibration point for the negative range.

Front Panel:

SCPI Command:

The third calibration point is automatically
selected. “Enter P3 measured data” should
be displayed.

CAL:LEV P3
*OPC?

Step 8. Measure the output voltage with the DMM and enter the data. The value

should be negative.

Front Panel:

SCPI Command:

Enter the value from the external DMM into
the data field and then select Next. When
calibration is complete, select Close

CAL:DATA <data>

Step 9. Repeat steps 1 through 5, 7 and 8 for the 600 mV range.

Low Range Voltage Measurement - Models N6781A, N6782A,
N6784A

Step 1. Select the low-voltage measurement range. The value entered must be

the maximum voltage of the range to be calibrated. This example selects
the 1 V range of output 1.

Front Panel:

SCPI Command:

From the Calibration menu, select
Voltage, Low Range Measurement. Then
select Start.

CAL:VOLT:MEAS 1

, (@1)

Step 2. Select the first voltage calibration point.

Содержание N6705








































































































































Результаты поиска

Содержание N6705

Отзывы:

Бренды по названию

Популярные бренды

Keysight N6705, Руководство по обслуживанию

Результаты поиска

Содержание N6705

Отзывы:

Бренды по названию

Популярные бренды