manualshive.com logo in svg

Keysight N6705, Руководство по обслуживанию

Поделиться
Скачать
Keysight N6705 Скачать руководство пользователя страница 15

Performance Verification    2 

Model N6705 Service Guide 

15 

CV Ripple and Noise 

Test category = performance 

Periodic and random deviations in the output combine to produce a 
residual AC voltage superimposed on the DC output voltage. This 
residual voltage is specified as the rms or peak-to-peak noise in the 
frequency range specified in the Keysight N6700 Modular Power System 
Family Specifications Guide. 

1

 

Turn off the DC Power Analyzer and connect a load resistor or 
electronic load, differential amplifier, and an oscilloscope (ac 
coupled) to the output (see Test Setup C).  

2

 

For models N6751A/52A, N6761A/62A, and N678xA SMU

 - use an 

appropriate load resistor to keep the DC Power Analyzer at the instrument 
setting specified in the test record form under “CV Ripple and Noise”. For 
all other power modules - use an electronic load to keep the DC Power 
Analyzer at the instrument setting specified in the test record form under 
“CV Ripple and Noise”. 

3

 

As shown in the diagram, use two BNC cables to connect the 
differential amplifier to the + and 

−

 output terminals. Each cable 

should be terminated by a 50 

Ω

 resistor. The shields of the two BNC 

cables should be connected together. Connect the output of the 
differential amplifier to the oscilloscope with a 50 

Ω

 termination at 

the input of the oscilloscope. 

4

 

Set the differential amplifier to multiply by ten, divide by one, and 1 
M

Ω

 input resistance. The positive and negative inputs of the 

differential amplifier should be set to AC coupling. Set the 
oscilloscope’s time base to 5 ms/div, and the vertical scale to 10 
mV/div. Turn the bandwidth limit on (usually 20 or 30 MHz), and set 
the sampling mode to peak detect. 

5

 

Program the DC Power Analyzer to the settings indicated in the in 
the test record form for the appropriate model under “CV Ripple and 
Noise” and enable the output. Let the oscilloscope run for a few 
seconds to generate enough measurement points. On the Keysight 
Infiniium scope, the maximum peak-to-peak voltage measurement is 
indicated at the bottom of the screen on the right side. Divide this 
value by 10 to get the CV peak-to-peak noise measurement. The 
result should not exceed the peak-to-peak limits in the test record 
form for the appropriate model under “CV Ripple and Noise, peak-
to-peak”.  

NOTE

 

If the measurement contains any question marks, clear the measurement 
and try again. This means that some of the scope data received was 
questionable. 

6

 

Disconnect the oscilloscope and connect an rms voltmeter in its 
place. Do not disconnect the 50 ohm termination. Divide the reading 
of the rms voltmeter by 10. The result should not exceed the rms 
limits in the test record form for the appropriate model under “CV 
Ripple and Noise, rms”. 

7

 

For models N6781A, N6782A, and N6784A only.

 Repeat steps 2 

through 6 for the 6 V range. 

Содержание N6705








































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды