Keysight Technologies InfiniVision 6000L Series Скачать руководство пользователя страница 89

Страница: 89 / 100

Replaceable Parts

6000L Series Oscilloscopes Service Guide

Exchange Assemblies

Some parts used in this instrument have been set up for an exchange program.

This program allows the customer to exchange a faulty assembly with one that

has been repaired, calibrated, and performance-verified by the factory. The cost is

significantly less than that of a new part. The exchange parts have a part number

in the form XXXXX-695XX.

After receiving the repaired exchange part from Keysight Technologies, a United

States customer has 30 days to return the faulty assembly. For orders not

originating in the United States, contact the local Keysight Technologies service

organization. If the faulty assembly is not returned within 30 days, the customer

will be charged an additional amount. The additional amount will be the difference

in price between a new assembly and that of an exchange assembly.

Содержание InfiniVision 6000L Series





































































































Результаты поиска

Содержание InfiniVision 6000L Series

Отзывы:

Похожие инструкции для InfiniVision 6000L Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniVision 6000L Series, Руководство по обслуживанию

Результаты поиска

Содержание InfiniVision 6000L Series

Отзывы:

Похожие инструкции для InfiniVision 6000L Series

Бренды по названию

Популярные бренды