Keysight Technologies InfiniVision 6000L Series Скачать руководство пользователя страница 61

Страница: 61 / 100

Troubleshooting

6000L Series Oscilloscopes Service Guide

• On 6000L Series models, press the power switch.

The Power indicator LED is green. The LAN indicator LED is bi-color (green

and/or red).

•

Shortly after pressing the power switch, the power indicator and LAN

indicator will illuminate.

•

Both will extinguish.

•

Both will illuminate again. If a LAN is connected, the LAN indicator will

illuminate red. It will turn green when the LAN is connected as it is

configured. The amount of time it takes the indicator to turn green depends

on the network and the oscilloscope’s LAN configuration setup.

Figure 9

6000L Series LED indicators

If the lights illuminate, then the power supply is probably working correctly.

Proceed to

“To verify basic oscilloscope operation"

on page 62.

WARNING

Always use a grounded power cord. Do not defeat the power cord ground.

LAN Status

Indicator

Power

Switch

Power

Indicator

Reset

Switch

Содержание InfiniVision 6000L Series





































































































Результаты поиска

Содержание InfiniVision 6000L Series

Отзывы:

Похожие инструкции для InfiniVision 6000L Series

Бренды по названию

Популярные бренды

Keysight Technologies InfiniVision 6000L Series, Руководство по обслуживанию

Результаты поиска

Содержание InfiniVision 6000L Series

Отзывы:

Похожие инструкции для InfiniVision 6000L Series

Бренды по названию

Популярные бренды