Kerlink 1LOC868-1W868-EU Скачать руководство пользователя страница 118

Страница: 118 / 221

Wirnet iBTS

Document title : Installation and
Maintenance Manual
Version : 2.0
Author : SNI
Date : 04/12/2018

Classification

This document is the strict property of Kerlink and shall not be either copied nor sent without express

written authorization of Kerlink

Internal Use

Kerlink m2m technologies reserved rights

Confidential

Kerlink – 1 rue Jacqueline Auriol – 35235 THORIGNÉ-FOUILLARD

Page 118 / 221

Strict confidential

Figure 80 : Dome antenna bracket dimensions

The dome antenna bracket has a single hole dedicated to the LTE and / or GPS M22 screw.
The dome antenna bracket can be mounted:

On a wall: use in this case 2 x M4 screws separated by 76mm (see figure above).

On a pole: use metallic strapping through the two 4mm x 25mm slots (see figure
above).

On a pole: alternate option is to use the “notched V shaped plate and a U-bolt” as
detailed in §1.8.6.1. The two parts are presented on the figure below. The maximum
diameter of the pole is 60mm.

Another slot is available. It can be used for cable ties to tighten the RF coaxial cable to the
antenna bracket.

Note 1:

the M4 screws, the metallic strapping are not provided by KERLINK.

Note 2:

the cables ties are not provided by KERLINK.

Note 3:

the notched V shaped plate and a U-bolt can be provided by KERLINK as accessories

(see §1.8.6.1).

Fixing holes
(wall mount)

Hole for antenna

Slots for metallic
strapping

Slot for cable tie

76 mm

Содержание 1LOC868-1W868-EU






























































































































































































































Результаты поиска

Содержание 1LOC868-1W868-EU

Отзывы:

Бренды по названию

Популярные бренды

Kerlink 1LOC868-1W868-EU, Руководство по установке и обслуживанию

Результаты поиска

Содержание 1LOC868-1W868-EU

Отзывы:

Бренды по названию

Популярные бренды