Kerbl CowCleaner 18700, Руководство по эксплуатации

Страница: 42 / 196

von
540 mm
1200 mm
670 mm
FLOOR
405 mm
540 mm
Ø13 mm
670 mm
FLOOR
Ø
Withers
height
Ø
Withers
height
Abb. 2
Abb. 3
STAT. REVISION NOTE DATE NAME Urspr.
2
3
A3
ASM
HappyCow UNO - Wall mounted
sreinthaler 4.8.2021
NORM
CHECK
DRAW
NAME DATE
DET. SCALE
1:10 1:20
SCALE
BASE SIZE/SEMI-FINISHED PART MATERIAL:
von
Blatt
27376
DWG NO.
TITLE:
ARTICLE NUMBER
KERBL:
18680; 18690; 18700
ISO 5456-2 Projection
methode1
Albert KERBL GmbH
l
Felizenzell 9
l
D-84428 Buchbach
Fon +49 (0)8086 - 933-100
l
Fax +49 (0)8086 - 933-500
Mail info@kerbl.com l www.kerbl.com
General tolerances
ISO 2768 - mK
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
PROJECT NUMBER
KERBL:
1310432,150 g
FINISHED SURFACE:
WEIGHT IN GRAMM
(WITHOUT FINISHED SURFACE):
von
540 mm
1200 mm
670 mm
FLOOR
405 mm
540 mm
Ø13 mm
670 mm
FLOOR
Ø
Withers
height
Ø
Withers
height
Abb. 2
Abb. 3
STAT. REVISION NOTE DATE NAME Urspr.
2
3
A3
ASM
HappyCow UNO - Wall mounted
sreinthaler 4.8.2021
NORM
CHECK
DRAW
NAME DATE
DET. SCALE
1:10 1:20
SCALE
BASE SIZE/SEMI-FINISHED PART MATERIAL:
von
Blatt
27376
DWG NO.
TITLE:
ARTICLE NUMBER
KERBL:
18680; 18690; 18700
ISO 5456-2 Projection
methode1
Albert KERBL GmbH
l
Felizenzell 9
l
D-84428 Buchbach
Fon +49 (0)8086 - 933-100
l
Fax +49 (0)8086 - 933-500
Mail info@kerbl.com
l
www.kerbl.com
General tolerances
ISO 2768 - mK
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
PROJECT NUMBER
KERBL:
1310432,150 g
FINISHED SURFACE:
WEIGHT IN GRAMM
(WITHOUT FINISHED SURFACE):
42
Tip
Secure the unit to an even, solid concrete wall.
5.3.1 Installation height
The suspension height of the unit must be adapted to the average withers height of the animals. The front lower edge of the brush should be at
the same height as the animals' average withers height (e.g. 1350 mm). The suspension height must be determined before the mounting holes
are made!
If there are considerable differences in withers height among the herd (more than 20 cm), the suspension height should be orientated towards the
larger animals in order to avoid rapid wear of the brushes.
Figure 2: Mounting height
Figure 3: Hole pattern
5.3.2 Installation steps
1. Determine the installation height (see Point 5.3.1)
2. Install the unit at the determined height.
3. If necessary, attach protection against chewing to the connection cable.
4. If necessary, attach the optional protection bar
Tip
The control with display, the contact switch and the motor are not visible or accessible from the outside. The machine can be swung away
from the wall to gain access to the contact switch and control and to view the display.
To do this, either loosen the two screw attachments on the left or right side of the machine connecting the basic platform to the external
housing. (Figure 4 + 5.)
Even during installation, ensure that the connection cable is positioned so that the machine can be swung away from the wall.