KEPCO KLP SERIES, Руководство оператора

Страница: 89 / 110

KLP 073008
B-3
FIGURE B-1. PROGRAMMING THE OUTPUT
B.7 INITiate:CONTinuous COMMAND
INIT:CONT
Syntax: Short Form: INIT:CONT {ON | OFF} or {1 | 0} (1 = on, 0 = off)
Long Form: INITiate:CONTinuous {ON | OFF} or {1 | 0} (1 = on, 0 = off)
Description: INIT:CONT ON enables continuous triggers.; INIT:CONT OFF disables continuous triggers. If
INIT:CONT is OFF, then INIT[:IMM] arms the trigger system for a single trigger. If INIT:CONT is ON,
then the trigger system is continuously armed and INIT[:IMM] is redundant. Executing *RST command
sets INIT:CONT to OFF. (See example, Figure B-1.)
B.8 INITiate:CONTinuous? QUERY
INIT:CONT?
Syntax : Short Form: INIT:CONT? Long Form: INITiate:CONTinuous?
Return Value: 1 or 0
Description: Determines whether continuous triggers are enabled or disabled. Power supply returns value of
INIT:CONT flag: “1” = continuous triggers are enabled (INIT:CONT ON); “0” = continuous triggers dis-
abled (INIT:CONT OFF). (See example, Figure B-1.)
B.9 [SOURce:]LIST:CLEar COMMAND
LIST:CLE
Syntax: Short Form: LIST:CLE Long Form: LIST:CLEar>
Description: Clears all list entries by setting all pointers to 0. Also sets LIST:DIR to UP, LIST:GEN to DSEQ,
Related Commands: All LIST commands (See example, Figure B-2.)
NOTE: The following example assumes KLP 75-33-1200 with virtual model set for 75V, 16A and output operating
in voltage stabilization mode. See Figure B-3 for directions on programming virtual model limits.
OUTP ON Enables output.
OUTP? Returns 1 (output enabled).
VOLT 75;CURR 1.5E-1 Programs output voltage to 75V, current limit to 0.15A.
INIT:CONT: ON Enables continuous triggering.
INIT:CONT? Returns 1 (continuous triggering enabled).
VOLT:TRIG 31.5;:CURR:TRIG3E-1 Programs output voltage for 31.5V, current limit for 0.3A upon receipt of trigger
stimulus.
*TRG Output voltage is set to 31.5V with 0.3A current limit.
VOLT 32.1;CURR 5E-2 Programs output voltage to 32.1V, current limit to 0.05A.
MEAS:VOLT? Returns actual output voltage (if output voltage is 32.15V, power supply
returns 3.215E1).
MEAS:CURR? Returns actual output current.
FUNC:MODE? Returns operating mode of power supply followed by programmed operating
mode, e.g., VOLT,VOLT.
CURR:TRIG? Returns 3E-1 (current value established by CURR:TRIG).
VOLT:TRIG? Returns 3.15E1 (voltage value established by VOLT:TRIG).
ABOR Changes pending trigger levels to immediate values (32.1V, 0.05A).
VOLT 37.7;CURR 2.5E-1 Programs output voltage to 37.7V, current limit to 0.25A.
*TRG Output returns to trigger values established by ABOR (32.1V, 0.05A).
INIT:CONT 0 Disables continuous triggering.
INIT:CONT? Returns 0 (continuous triggering disabled).
OUTP OFF Output disabled.
OUTP? Returns 0 (output disabled).
MEAS:VOLT? Returns 0 (measured output voltage).
VOLT? Returns 3.21E1 (last programmed output voltage).
CURR? Returns 5E-2 (last programmed output current).
CURR? MAX Returns 1.6E1 (maximum allowable current for present virtual model).
CURR? MIN Returns 4E-1 (minimum allowable programming current for model).