Keltron FDACT Скачать руководство пользователя | Manualshive

Страница: 55 / 60

background image

49

Mirtone MIR2

The MIR2 allocates fixed ranges of 4-digit point IDs to all detectors, modules, and notification appliance
circuits either connected directly to the MIR2-MCM main controller module or to the MIR2-LCX
Expander module. In addition the MIR2 assigns unique point IDs to various panel faults, for example
point 0003 is assigned to Battery fault and point 0005 is assigned to Ground fault. Please refer to the
MIR2 System Operations Manual for a complete list of faults and point IDs.

No conversion is necessary for the detectors, modules, and notification appliance circuit point IDs. Those
point IDs are transmitted directly as the 4-digit SIA zone number. The MIR2 panel fault point IDs are
converted to different SIA zone numbers so there is no conflict with the SDACT’s hardwired zone
numbers.

The conversion rules are summarized in the following table:

CATEGORY

MIR2 POINT

SIA ZONE

MIR2-MCM Detectors

0101 to 0196

0101 to 0196

MIR2-MCM NAC

0201 to 0202

0201 to 0202

MIR2-MCM Modules

0203 to 0296

0203 to 0296

MIR2-LCX Detectors

0301 to 0396

0301 to 0396

MIR2-LCX NAC

0401 to 0402

0401 to 0402

MIR2-LCX Modules

0403 to 0496

0403 to 0496

Faults

0001 to 0029

0601 to 0629

Faults

xx97 to xx99

0797 to 0799

«
...
53
54
55
56
57
...
»

Содержание FDACT





























































Отзывы:

Нет отзывов

Похожие инструкции для FDACT

Бренд: Bosch Страницы: 40

Бренд: Bosch Страницы: 34

Бренд: Bosch Страницы: 32

AVENAR 4000 FAH-425-T-R

Бренд: Bosch Страницы: 38

Бренд: Bosch Страницы: 82

Бренд: Bosch Страницы: 2

Бренд: Ampac Страницы: 25

Бренд: Ampac Страницы: 22

Бренд: E2S Страницы: 8

Бренд: Zeta Страницы: 32

Бренд: Eaton Страницы: 80

Synergy Zone Leader

Бренд: Evacuator Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды