Keltron FDACT Скачать руководство пользователя | Manualshive

Страница: 53 / 60

background image

47

Edwards System Technology EST2

The EST2 allocates fixed ranges of 4-digit point IDs to all detectors, modules, and notification appliance
circuits either connected directly to the 2-MCM main controller module or to the 2-LCX Expander
module. In addition the EST2 assigns unique point IDs to various panel faults, for example point 0003 is
assigned to Battery fault and point 0005 is assigned to Ground fault. Please refer to the EST2 System
Operations Manual for a complete list of faults and point IDs.

No conversion is necessary for the detectors, modules, and notification appliance circuit point IDs. Those
point IDs are transmitted directly as the 4-digit SIA zone number. The EST2 panel fault point IDs are
converted to different SIA zone numbers so there is no conflict with the SDACT’s hardwired zone
numbers.

The conversion rules are summarized in the following table:

CATEGORY

EST2 POINT

SIA ZONE

2-MCM Detectors

0101 to 0196

0101 to 0196

2-MCM NAC

0201 to 0202

0201 to 0202

2-MCM Modules

0203 to 0296

0203 to 0296

2-LCX Detectors

0301 to 0396

0301 to 0396

2-LCX NAC

0401 to 0402

0401 to 0402

2-LCX Modules

0403 to 0496

0403 to 0496

Faults

0001 to 0029

0601 to 0629

Faults

xx97 to xx99

0797 to 0799

«
...
51
52
53
54
55
...
»

Содержание FDACT





























































Отзывы:

Нет отзывов

Похожие инструкции для FDACT

Бренд: C-TEC Страницы: 2

Бренд: LIFETONE Страницы: 2

ECLIPSE CAFSystem 2.0

Бренд: Waterous Страницы: 44

Бренд: UniPOS Страницы: 2

Бренд: SANJIANG Страницы: 7

Бренд: United Technologies Страницы: 2

Бренд: GFS Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды