Keltron FDACT Скачать руководство пользователя | Manualshive

Страница: 46 / 60

background image

40

If telephone line faults are reported and the phone line is operable, measure the voltage across the phone
line connection terminals and report the findings to Keltron Corporation technical support.

The S/FDACT may be reset or powered down. This will clear all events pending transmission from
memory.

Service

Please refer all service issues to a Keltron certified alarm technician. This device cannot be adjusted or
repaired in the field. The S/FDACT does not contain field serviceable components and therefore is not
field serviceable.

In case of trouble with the Keltron S/FDACT, notify the installing company or return the S/FDACT to the
manufacturer.

Contact Information

KELTRON HEADQUARTERS
Keltron Corporation
101A First Avenue
Waltham, Massachusetts 02451
Telephone: 781-894-8710
Toll Free: 800-966-6123
FAX: 781-899-9652
Email:

[email protected]

GENERAL
Telephone: 781-894-8710
Email:

[email protected]

SALES
Telephone: 781-894-8710 ext 2054
Email:

[email protected]

SUPPORT & SERVICES
Telephone: 781-894-8710 ext 2077
Email:

[email protected]

Keltron develops and manufactures secure, reliable, UL-listed fire and security alarm response
management systems and components for the municipal and proprietary life safety markets. Products
include radio fire alarm, coded fire alarm and high-line security systems, digital alarm receivers,
universally compatible fire alarm control panel networking solutions and a full line of alarm annunciators.
Fore more information, visit

www.keltroncorp.com

or contact us at 781-894-8710 ext 2054, or

[email protected]

.



Keltron Corporation. All rights reserved.

«
...
44
45
46
47
48
...
»

Содержание FDACT





























































Отзывы:

Нет отзывов

Похожие инструкции для FDACT

Бренд: Fire-Lite Alarms Страницы: 2

Бренд: Wheelock Страницы: 9

SIMPLICITY MICRO

Бренд: Zeta Alarm Systems Страницы: 28

Бренд: VENTCROFT Страницы: 5

Notifier LCD2-80

Бренд: Honeywell Страницы: 24

Бренд: Honeywell Страницы: 49

Silent Knight 6820EVS

Бренд: Honeywell Страницы: 5

Бренд: Siemens Страницы: 4

Бренд: GE Страницы: 6

Бренд: GST Страницы: 2

Бренд: GST Страницы: 2

Бренд: GST Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды